SAE-J2399-2003 ADAPTIVE CRUISE CONTROL (ACC) OPERATING CHARACTERISTICS AND USER INTERFACE
SAE-J2400-2003 HUMAN FACTORS IN FORWARD COLLISION WARNING SYSTEMS: OPERATING CHARACTERISTICS AND USER INTERFACE REQUIREMENTS
SAE-J240-2002 LIFE TEST FOR AUTOMOTIVE STORAGE BATTERIES
SAE-J2402-1997 ROAD VEHICLES - SYMBOLS FOR CONTROLS, INDICATORS, AND TELL-TALES - ISO 2575
SAE-J2403-2004 MEDIUM/HEAVY-DUTY E/E SYSTEMS DIAGNOSIS NOMENCLATURE
SAE-J2405-1997 LOW-PERMEATION FUEL FILL AND VENT TUBE
SAE-J2406-2002 RECOMMENDED PRACTICES FOR CNG POWERED MEDIUM AND HEAVY-DUTY TRUCKS
SAE-J2407-1997 CLUTCH INSTALLATION AND RELEASE LINKAGE REQUIREMENTS FOR TRUCK AND BUS APPLICATION
SAE-J2408-1997 CLUTCH REQUIREMENTS FOR HIGH-TORQUE TRUCK AND BUS ENGINES
SAE-J2409-2004 (R) STRAIN-LIFE FATIGUE DATA FILE FORMAT
SAE-J2411-2000 SINGLE WIRE CAN NETWORK FOR VEHICLE APPLICATIONS
SAE-J2412-2004 ACCELERATED EXPOSURE OF AUTOMOTIVE INTERIOR TRIM COMPONENTS USING A CONTROLLED IRRADIANCE XENON-ARC APPARATUS
SAE-J2413-2003 PROTOCOL TO VERIFY PERFORMANCE OF NEW XENON ARC TEST APPARATUS
SAE-J2414-2005 APPLICATION TESTING OF OIL-TO-WATER OIL COOLERS FOR HEAT TRANSFER PERFORMANCE
SAE-J2417-2004 LIFT CAPACITY CALCULATION METHOD KNUCKLE-BOOM LOG LOADERS AND CERTAIN FORESTRY EQUIPMENT
SAE-J2418-1998 OCCUPANT RESTRAINT SYSTEM EVALUATIONFRONTAL IMPACT COMPONENT-LEVEL HEAVY TRUCKS
SAE-J2419-1998 OCCUPANT RESTRAINT SYSTEM EVALUATIONFRONTAL IMPACT SYSTEM-LEVEL HEAVY TRUCKS
SAE-J2420-2003 COE FRONTAL STRENGTH EVALUATION - DYNAMIC LOADING HEAVY TRUCKS
SAE-J2422-2003 CAB ROOF STRENGTH EVALUATION - QUASI-STATIC LOADING HEAVY TRUCKS
SAE-J2424-1998 FREE MOTION HEADFORM IMPACT TESTS OF HEAVY TRUCK CAB INTERIORS
SAE-J2425-2004 STEERING CONTROL SYSTEMS - LABORATORY TEST PROCEDURE HEAVY TRUCKS
SAE-J2426-1998 OCCUPANT RESTRAINT SYSTEM EVALUATIONLATERAL ROLLOVER SYSTEM-LEVEL HEAVY TRUCKS
SAE-J2429-2004 FREE-ROLLING CORNERING TEST FOR TRUCK AND BUS TIRES
SAE-J2430-1999 DYNAMOMETER EFFECTIVENESS CHARACTRIZATION TEST FOR PASSENGER CAR AND LIGHT TRUCK BRAKE FRICTION PRODUCTS
SAE-J2431-1997 EFFECTS OF FRONT-MOUNTED ACCESSORIES ON AIR BAG SENSORS AND CRASHWORTHINESS
SAE-J243-1971 METHODS OF TESTS FOR AUTOMOTIVE-TYPE SEALERS, ADHESIVES, AND DEADENERS - OCTOBER 1971
SAE-J2432-2000 PERFORMANCE TESTING OF PK SECTION V-RIBBED BELTS
SAE-J2435-1999 WELDED FLASH CONTROLLED, SAE 1021 CARBON STEEL TUBING, NORMALIZED FOR BENDING, DOUBLE FLARING, AND BEADING
SAE-J2436-1998 ACCESSORY DRIVE TENSIONER TEST STANDARDS (MECHANICAL ROTARY TYPE)
SAE-J2437-1998 AIR STARTER MOTOR TEST PROCEDURES
SAE-J2438-1998 LOW-TEMPERATURE CRANKING LOAD REQUIREMENTS OF AN ENGINE - AIR STARTER METHOD
SAE-J2440-1998 DOMESTIC PERFORMANCE TORQUE CONVERTER MANUFACTURING
SAE-J2441-2000 SHOT PEENING
SAE-J244-1992 (R) MEASUREMENT OF INTAKE AIR OR EXHAUST GAS FLOW OF DIESEL ENGINES - AUGUST 1992
SAE-J2442-2000 HARMONIZED PROVISIONS FOR INSTALLATION OF LAMPS AND RETRO-REFLECTING DEVICES ON ROAD VEHICLES EXCEPT

MOTORCYCLES
SAE-J2450-2005 TRANSLATION QUALITY METRIC
SAE-J2452-1999 STEPWISE COASTDOWN METHODOLOGY FOR MEASURING TIRE ROLLING RESISTANCE
SAE-J2453-1999 MANUAL TRANSMISSION AND TRANSAXLE EFFICIENCY AND PARASITIC LOSS MEASUREMENT
SAE-J2455-1998 DRIVETRAIN SYSTEMS VIBRATION ANALYSIS DATA REQUIREMENTS
SAE-J2456-1998 MERCURY SWITCH REMOVAL PROCESS
SAE-J2457-2001 AIR QUALITY FOR AIR BRAKED VEHICLES
SAE-J2458-1998 EXHAUST BRAKE DYNAMOMETER TEST AND CAPABILITY RATING PROCEDURE
SAE-J2461-2002 VEHICLE ELECTRONIC PROGRAMMING STATIONS (VEPS) SYSTEM SPECIFICATION FOR WIN32
SAE-J246-2000 SPHERICAL AND FLANGED SLEEVE (COMPRESSION) TUBE FITTINGS
SAE-J2464-1999 ELECTRIC VEHICLE BATTERY ABUSE TESTING
SAE-J2467-1999 WELDED AND COLD-DRAWN, SAE 1021 CARBON STEEL TUBING NORMALIZED FOR BENDING AND FLARING
SAE-J2468-1999 ROAD VEHICLES - BRAKE LININGS - COMPRESSIBILITY TEST PROCEDURE
SAE-J2469-1999 CLUTCH APPLICATION POWERTRAIN STARTABILITY RATING REQUIREMENTS FOR TRUCK AND BUS APPLICATONS
SAE-J2470-1999 HYDRAULIC FLUID POWER - VALVES - METHOD FOR ASSESSING THE LOCK SENSITIVITY TO CONTAMINANTS
SAE-J24714-2001 FLUID SYSTEMS - CONNECTOR TUBES - GENERAL SPECIFICATION AND PART STANDARD
SAE-J247-1974 INSTRUMENTATION FOR MEASURING ACOUSTIC IMPULSES WITHIN VEHICLES
SAE-J2473-2001 SELF-PROPELLED SWEEPERS AND SCRUBBERS - MAXIMUM GRADIENT RATING DURING HOPPER DISCHARGE        
SAE-J2474-2000 SELF PROPELLED SWEEPERS AND SCRUBBERS BATTERY RUN-TIME
SAE-J2475-2005 WHEEL END ASSEMBLY AND AXLE SPINDLE INTERFACE DIMENSIONS - TRUCK AND BUS
SAE-J2477-2004 AUTOMOTIVE AUSTEMPERED DUCTILE (NODULAR) IRON CASTINGS (ADI)
SAE-J2481-1999 DYNAMIC SIMULATION SLED TESTING
SAE-J2484-2002 FASTENER PART STANDARDMACHINE SCREWS
SAE-J2485-2003 FASTENER PART STANDARD - MACHINE SCREW NUTS (METRIC AND INCH)
SAE-J2486-1999 TENSION INDICATING WASHER TIGHTENING METHOD FOR FASTENERS
SAE-J2487-2000 SAE NO.2 FRICTION TEST MACHINE 3600 R/MIN STEPPED POWER TEST
SAE-J2489-2000 SAE NO.2 FRICTION TEST MACHINE DURABILITY TEST
SAE-J2490-2000 SAE NO.2 FRICTION TEST MACHINE UPVT TEST
SAE-J249-1988 MECHANICAL STOP LAMP SWITCH - JUNE 1988
SAE-J2492-1999 CONSIDERATIONS FOR SUSPENSION MODIFICATION
SAE-J2494-1-2004 DIMENSIONAL SPECIFICATIONS FOR METALLIC BODY PUSH-TO-CONNECT FITTINGS USED ON A VEHICULAR AIR BRAKE SYSTEM -

SUPERSEDING J2494
SAE-J2494-2-2002 DIMENSIONAL SPECIFICATIONS FOR NON-METALLIC BODY PUSH-TO-CONNECT FITTINGS USED ON A VEHICULAR AIR BRAKE

SYSTEM
SAE-J2494-3-2002 PERFORMANCE REQUIREMENTS FOR SAE J844 NON-METALLIC AIR BRAKE TUBING AND PUSH TO CONNECT FITTING ASSEMBLIES

USED IN VEHICULAR AIR BRAKE SYSTEMS
SAE-J2494-4-2002 CARTRIDGE CAVITY
SAE-J2495-1999 THERMAL CONTAINMENT EFFICIENCY OF SLEEVE MATERIALS
SAE-J2496-2000 TRANSPORT AREA NETWORK CABLING
SAE-J2497-2002 POWER LINE CARRIER COMMUNICATIONS FOR COMMERCIAL VEHICLES
SAE-J2498-1999 MINIMUM PERFORMANCE OF THE WARNING LIGHT SYSTEM USED ON EMERGENCY VEHICLES
SAE-J2501-2001 ROUND, UNSCREENED, 60 V AND 600 V MULTICORE SHEATHED CABLES
SAE-J250-1959 SYNTHETIC RESIN PLASTIC SEALERS, NONDRYING TYPE - MAY 1959
SAE-J2503-2000 DRAWBAR PULL PERFORMANCE CRITERIA
SAE-J2505-2003 MEASUREMENT OF VEHICLE-ROADWAY FRICTIONAL DRAG
SAE-J2506-2000 MATERIAL HANDLER NOMENCLATURE
SAE-J2512-1999 TOWING EQUIPMENT RATINGS AND PRACTICES
SAE-J2513-2000 EARTHMOVING MACHINERY - COUPLING OF ATTACHMENTS TO SKID STEER LOADERS
SAE-J2515-1999 HIGH TEMPERATURE MATERIALS FOR EXHAUST MANIFOLDS
SAE-J2517-2000 HYBRID III FAMILY CHEST POTENTIOMETER CALIBRATION PROCEDURE
SAE-J2518-2003 LIFT CAPACITY CALCULATION METHOD SCRAP AND MATERIAL HANDLERS
SAE-J2519-2002 GUIDELINES AND PROCEDURES FOR DIRECTIONAL DRILLING TRACKING OPERATORS
SAE-J2520-2002 CLASSIFICATION, NOMENCLATURE, AND SPECIFICATION DEFINITIONS FOR DIRECTIONAL DRILLING TRACKING EQUIPMENT
SAE-J2521-2006 (R) DISC AND DRUM BRAKE DYNAMOMETER SQUEAL NOISE MATRIX
SAE-J2522-2003 DYNAMOMETER GLOBAL BRAKE EFFECTIVENESS
SAE-J2523-2003 ROLLING CIRCUMFERENCE INDEX GROUPS FOR RADIAL TRACTOR DRIVE TIRES
SAE-J2525-2000 SAE DESIGN GUIDELINE: METAL BELT DRIVE CONTINUOUSLY VARIABLE RATIO (CVT) AUTOMATIC TRANSMISSIONS
SAE-J2527-2004 PERFORMANCE BASED STANDARD FOR ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A CONTROLLED

IRRADIANCE XENON-ARC APPARATUS
SAE-J2530-2004 AFTERMARKET WHEELS-PASSENGER CARS AND LIGHT TRUCK - PERFORMANCE REQUIREMENTS AND TEST PROCEDURES
SAE-J2531-2003 IMPULSE NOISE FROM AUTOMOTIVE INFLATABLE DEVICES
SAE-J253-1984 HEADLAMP SWITCH
SAE-J2534-1-2004 (R) RECOMMENDED PRACTICE FOR PASS-THRU VEHICLE PROGRAMMING
SAE-J2534-2-2006 OPTIONAL PASS-THRU FEATURES
SAE-J2535-2001 SETTING PRELOAD IN HEAVY-DUTY WHEEL BEARINGS
SAE-J2536-2004 ANTI-LOCK BRAKE SYSTEM (ABS) ROAD TEST EVALUATION PROCEDURE FOR TRUCK-TRACTORS AND BUSES
SAE-J2539-2002 COMPARISON OF GATS MESSAGES TO SAE ATIS STANDARDS
SAE-J2540-1-2002 RDS PHRASE LISTS
SAE-J2540-2002 MESSAGES FOR HANDLING STRINGS AND LOOK-UP TABLES IN ATIS STANDARDS
SAE-J2540-2-2004 (R) ITIS PHRASE LISTS (INTERNATIONAL TRAVELER INFORMATION SYSTEMS)
SAE-J2540-3-2002 NATIONAL NAMES PHRASE LIST
SAE-J254-1993 (R) INSTRUMENTATION AND TECHNIQUES FOR EXHAUST GAS EMISSIONS MEASUREMENT - SEPTEMBER 1993
SAE-J2542-2001 SELF-PROPELLED SWEEPERS AND SCRUBBERS FUEL CONSUMPTION OF NON-PROPULSION AUXILIARY ENGINES
SAE-J2544-2000 PLUG-IN RELAY TEST METHODS
SAE-J2545-2001 TEST PROCEDURES FOR NON-SAE HYDRAULIC HOSES
SAE-J2546-2002 MODEL SPECIFICATION PROCESS STANDARD
SAE-J2548-2001 TEST METHOD TO OBTAIN LUG-UP TORQUE DATA FOR HEAVY-DUTY TRUCK AND BUS ENGINES
SAE-J2551-2001 RECOMMENDED PRACTICES FOR FLUID CONDUCTOR METALLIC TUBING APPLICATIONS
SAE-J2554-2003 ENGINE INTAKE AIR WATER SEPARATION TEST PROCEDURE
SAE-J2555-2000 VEHICLE IDLE GEAR RATTLE EVALUATION PROCEDURE
SAE-J2556-2000 RADIATED EMISSIONS (RE) NARROWBAND DATA ANALYSIS - POWER SPECTRAL DENSITY (PSD)
SAE-J2558-2005 CLASSIFICATION SYSTEM FOR THERMOPLASTIC ELASTOMERS
SAE-J2561-2001 BLUETOOTH WIRELESS PROTOCOL FOR AUTOMOTIVE APPLICATIONS
SAE-J2562-2005 BIAXIAL WHEEL FATIGUE TEST
SAE-J2564-2004 AUTOMOTIVE STABILITY ENHANCEMENT SYSTEMS
SAE-J2566-2005 PERSONAL WATERCRAFTDISPLAY OF PERSONS CAPACITY INFORMATION
SAE-J2567-2004 MEASUREMENT OF EXHAUST SOUND LEVELS OF STATIONARY SNOWMOBILES
SAE-J2568-2003 INTRUSION RESISTANCE OF SAFETY GLAZING SYSTEMS FOR ROAD VEHICLES
SAE-J2570-2001 PERFORMANCE SPECIFICATIONS FOR ANTHROPOMORPHIC TEST DEVICE TRANSDUCERS
SAE-J2571-2003 ADVANCED DRIVER INTERFACE SYSTEMS FOR COMMERCIAL VEHICLE OPERATIONS
SAE-J257-1997 (R) BRAKE RATING HORSEPOWER REQUIREMENTS-COMMERCIAL VEHICLES
SAE-J2574-2002 FUEL CELL VEHICLE TERMINOLOGY
SAE-J2575-2004 STANDARDIZED DENT RESISTANCE TEST PROCEDURE
SAE-J2576-2002 BLADE FUSES - 42 V SYSTEM
SAE-J2577-2005 HEAVY DUTY LAMP ELECTRICAL CONNECTOR STANDARD
SAE-J2578-2002 RECOMMENDED PRACTICE FOR GENERAL FUEL CELL VEHICLE SAFETY
SAE-J2580-2005 IDENTIFICATION AND INSTALLATION OF AIR BRAKE SYSTEM COMPONENTS
SAE-J2581-2003 THERMAL TRANSPORT PROPERTIES GERMANE TO FRICTION MATERIALS AND BRAKES
SAE-J2582-2004 AUTOMOTIVE DUCTILE IRON CASTINGS FOR HIGH TEMPERATURE APPLICATIONS
SAE-J2583-2002 DIRECTIONAL DRILLING PLANNING AND MAPPING NOMENCLATURE
SAE-J2584-2002 HEADLAMP MOUNTING HEIGHT FOR PASSENGER AND PICKUP TRUCK VEHICLES
SAE-J2587-2005 OPTIMIZED FUEL TANK SENDER CLOSURE
SAE-J2588-2004 REMOTE STEERING CONTROL SYSTEMS
SAE-J2590-2001 PMODE FOR IN-VEHICLE NETWORKS
SAE-J2591-2002 ADAPTIVE FORWARD LIGHTING SYSTEM
SAE-J259-1971 IGNITION SWITCH - JUNE 1971
SAE-J2593-2006 INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS
SAE-J2594-2003 RECOMMENDED PRACTICE TO DESIGN FOR RECYCLING PROTON EXCHANGE MEMBRANE (PEM) FUEL CELL SYSTEMS
SAE-J2595-2006 PERFORMANCE REQUIREMENTS FOR SEALED BEAM MOTOR VEHICLE HEADLAMPS - SUPERSEDES SAE J1383:12/1996
SAE-J2596-2004 FASTENER PART STANDARDTAPPING SCREWS AND METALLIC DRIVE SCREWS (INCH DIMENSIONED)
SAE-J2598-2006 AUTOMOTIVE DISC BRAKE PAD NATURAL FREQUENCY AND DAMPING TEST
SAE-J2599-2003 FUEL FILLER PIPE ASSEMBLY DESIGN PRACTICE TO MEET LOW EVAPORATIVE EMISSION REQUIREMENTS
SAE-J2600-2002 COMPRESSED HYDROGEN SURFACE VEHICLE REFUELLING CONNECTION DEVICES
SAE-J2602-1-2005 LIN NETWORK FOR VEHICLE APPLICATIONS
SAE-J2602-2-2005 LIN NETWORK FOR VEHICLE APPLICATIONS CONFORMANCE TEST
SAE-J2603-2004 POWERED GAS/BRAKE CONTROL SYSTEMS
SAE-J2605-2001 NON-CONTACT HOSE MEASUREMENT STUDY 1
SAE-J2606-2003 DRAIN AND FILL PLUG FOR USE ON ENGINES, TRANSMISSIONS, AND AXLES
SAE-J2608-2003 OFF THROTTLE STEERING CAPABILITIES OF PERSONAL WATERCRAFT
SAE-J2609-2003 MULTI-DIMENSIONAL THERMAL PROPERTIES OF INSULATED HEAT SHIELD MATERIAL SYSTEMS
SAE-J2610-2002 SERIAL DATA COMMUNICATION INTERFACE
SAE-J2612-2002 INTERNAL COMBUSTION ENGINESPISTON VOCABULARY
SAE-J2613-2002 WELDED FLASH CONTROLLED, HIGH STRENGTH LOW ALLOY STEEL HYDRAULIC TUBING, SUB-CRITICALLY ANNEALED FOR BENDING,

DOUBLE FLARING, AND BENDING
SAE-J2614-2003 WELDED AND COLD-DRAWN, HIGH STRENGTH LOW ALLOY STEEL HYDRAULIC TUBING, SUB-CRITICALLY ANNEALED FOR BENDING AND

FLARING
SAE-J2615-2005 TESTING PERFORMANCE OF FUEL CELL SYSTEMS FOR AUTOMOTIVE APPLICATIONS
SAE-J2616-2005 TESTING PERFORMANCE OF THE FUEL PROCESSOR SUBSYSTEM OF AN AUTOMOTIVE FUEL CELL SYSTEM
SAE-J2621-2004 QUALIFYING AFTERMARKET TWO-COMPONENT STRUCTURAL FOAMS
SAE-J2622-2003 BATTERY CONNECTIONS FOR 42 VOLT ELECTRICAL SYSTEMS TESTS AND GENERAL PERFORMANCE REQUIREMENTS
SAE-J2623-2002 STANDARD RAINFLOW FILE FORMAT
SAE-J2624-2003 DRAFT COMPREHENSIVE LINING EVALUATION - VEHICLE
SAE-J2627-2002 COMMERCIAL VEHICLE BRAKING SYSTEM DEFINITIONS
SAE-J2628-2005 (R) CHARACTERIZATION, CONDUCTED IMMUNITY
SAE-J2630-2003 CONVERTING ATIS MESSAGE STANDARDS FROM ASN.1 TO XML
SAE-J2631-2006 DEFINING HYDRAULIC OIL COMPATIBILITY WITH HYDRAULIC HOSE ELASTOMERS
SAE-J2634-2003 SCRIBING OF COATINGS IN PREPARATION FOR TESTING OF WHEELS AND WHEEL TRIM
SAE-J2636-2006 CORROSION TEST MASTER ESTABLISHMENT
SAE-J2638-2003 FIFTH WHEEL AND GOOSENECK ATTACHMENT PERFORMANCE UP TO 13 608/KG (30 000/LB) TRAILER GVW
SAE-J2640-2006 GENERAL AUTOMOTIVE EMBEDDED SOFTWARE DESIGN REQUIREMENTS
SAE-J264-1998 VISION GLOSSARY
SAE-J2642-2004 RECOMMENDED PRACTICE FOR DEVELOPING SPECIFICATIONS FOR AUTOMOTIVE THERMOPLASTIC MATERIALS
SAE-J2643-2004 STANDARD REFERENCE ELASTOMERS (SRE) FOR CHARACTERIZING THE EFFECT OF LIQUIDS ON VULCANIZED RUBBERS
SAE-J2645-2003 LIQUEFIED NATURAL GAS (LNG) VEHICLE METERING AND DISPENSING SYSTEMS
SAE-J2649-2004 STRAIN-LIFE OVERLOAD FATIGUE DATA FILE FORMAT
SAE-J2650-2005 PERFORMANCE REQUIREMENTS FOR LIGHT EMITTING DIODE (LED) ROAD ILLUMINATION DEVICE SYSTEMS
SAE-J2651-2005 JUMP START CONNECTIONS FOR 42 VOLT ELECTRICAL SYSTEMS
SAE-J265-1991 DIESEL FUEL INJECTOR ASSEMBLY - TYPES 8, 9, 10, AND 11
SAE-J2654-2004 HARDNESS OF BRAKE LINING
SAE-J2655-2003 FASTENER PART STANDARDWASHERS AND LOCKWASHERS (INCH DIMENSIONED)
SAE-J2656-2003 FASTENER PART STANDARD HEXAGON SOCKET, SQUARE HEAD, AND SLOTTED HEADLESS SET SCREWS - INCH DIMENSIONED
SAE-J2657-2004 TIRE PRESSURE MONITORING SYSTEMS FOR LIGHT DUTY HIGHWAY VEHICLES
SAE-J2658-2003 METALLIC TUBE CONDUCTOR ASSEMBLIES FOR FLUID POWER AND GENERAL USETEST METHODS FOR HYDRAULIC FLUID POWER

METALLIC TUBE ASSEMBLIES
SAE-J2659-2003 TEST METHOD TO MEASURE FLUID PERMEATION OF POLYMERIC MATERIALS BY SPECIATION
SAE-J266-1996 STEADY-STATE DIRECTIONAL CONTROL TEST PROCEDURES FOR PASSENGER CARS AND LIGHT TRUCKS
SAE-J2662-2003 TORQUE RATINGS FOR POWER TAKE-OFF MOUNTING PADS
SAE-J2666-2003 HOSE GAUGE EVALUATION PROCEDURE
SAE-J2667-2004 STRSW (SQUEEZE TYPE RESISTANCE SPOT WELDING) EQUIPMENT ACCEPTANCE CRITERIA FOR THE COLLISION REPAIR INDUSTRY
SAE-J2669-2006 VOLTAGE REGULATORS FOR AUTOMOTIVE-TYPE GENERATORS
SAE-J2670-2005 STABILITY AND COMPATIBILITY CRITERIA FOR ADDITIVES AND FLUSHING MATERIALS INTENDED FOR USE IN VEHICLE AIR-

CONDITIONING SYSTEMS USING R-134A
SAE-J2671-2004 REDUCED EFFORT BRAKES AND REDUCED EFFORT VACUUM POWERED BRAKE BACKUP SYSTEMS
SAE-J267-1999 (R) WHEELS/RIMS - TRUCKS - PERFORMANCE REQUIREMENTS AND TEST PROCEDURES
SAE-J2672-2004 REDUCED EFFORT POWER STEERING AND POWER STEERING BACKUP SYSTEMS
SAE-J2673-2004 STRAIGHT-LINE BRAKING TEST FOR TRUCK AND BUS TIRES
SAE-J2675-2004 COMBINED CORNERING AND BRAKING TEST FOR TRUCK TIRES
SAE-J2678-2004 NAVIGATION AND ROUTE GUIDANCE FUNCTION ACCESSIBILITY WHILE DRIVING RATIONALE
SAE-J2679-2004 CHARGE AIR COOLER LEAKAGE
SAE-J268-2004 REAR VIEW MIRRORS - MOTORCYCLES
SAE-J2683-2005 REFRIGERANT PURITY AND CONTAINER REQUIREMENTS FOR CARBON DIOXIDE (CO2 R-744) USED IN MOBILE AIR-CONDITIONING

SYSTEMS
SAE-J2685-2006 POSITIVE TEMPERATURE COEFFICIENT OVERCURRENT PROTECTION DEVICES (PTCS)
SAE-J2695-2005 HEAVY DUTY VEHICLE LUBRICATING GREASES
SAE-J2704-2005 TIRE NORMAL FORCE/DEFLECTION AND GROSS FOOTPRINT DIMENSION TEST
SAE-J2705-2005 TIRE QUASI-STATIC ENVELOPMENT OF TRIANGULAR/STEP CLEATS TEST
SAE-J2707-2005 WEAR TEST PROCEDURE ON INERTIA DYNAMOMETER FOR BRAKE FRICTION MATERIALS
SAE-J2710-2005 MODAL TESTING AND IDENTIFICATION OF LOWER ORDER TIRE NATURAL FREQUENCIES OF RADIAL TIRES
SAE-J2711-2002 RECOMMENDED PRACTICE FOR MEASURING FUEL ECONOMY AND EMISSIONS OF HYBRID-ELECTRIC AND CONVENTIONAL HEAVY-DUTY

VEHICLES
SAE-J2717-2006 TESTS TO DEFINE TIRE SIZE (GEOMETRY), MASS, AND INERTIAS
SAE-J2718-2006 TEST FOR TIRE QUASI-STATIC LONGITUDINAL FORCE VS. LONGITUDINAL DISPLACEMENT AND QUASI-STATIC LATERAL FORCE VS.

LATERAL DISPLACEMENT
SAE-J2719-2005 INFORMATION REPORT ON THE DEVELOPMENT OF A HYDROGEN QUALITY GUIDELINE FOR FUEL CELL VEHICLES
SAE-J272-1981 VEHICLE IDENTIFICATION NUMBER SYSTEMS - DECEMBER 1981
SAE-J2723-2005 ENGINE POWER TEST CODEENGINE POWER AND TORQUE CERTIFICATION
SAE-J2727-2005 MOBILE AIR CONDITIONING SYSTEM LEAKAGE CHART
SAE-J2738-2005 IMPROVED ROADWAY ILLUMINATION: INFORMATION RESOURCE
SAE-J2740-2005 GENERAL MOTORS UART SERIAL DATA COMMUNICATIONS
SAE-J2760-2006 PRESSURE TERMINOLOGY USED IN FUEL CELLS AND OTHER HYDROGEN VEHICLE APPLICATIONS
SAE-J276-1992 STEERING FRAME LOCK FOR ARTICULATED LOADERS AND TRACTORS
SAE-J277-1990 MAINTENANCE OF DESIGN VOLTAGE - SNOWMOBILE ELECTRICAL SYSTEMS
SAE-J278-2006 SNOWMOBILE STOP LAMP
SAE-J279-2006 SNOWMOBILE TAIL LAMP (REAR POSITION LAMP)
SAE-J280-2006 SNOWMOBILE HEADLAMPS
SAE-J283-1993 TEST PROCEDURE FOR MEASURING HYDRAULIC LIFT CAPACITY ON AGRICULTURAL TRACTORS EQUIPPED WITH THREE-POINT HITCH
SAE-J284-1975 SAFETY ALERT SYMBOL FOR AGRICULTURAL, CONSTRUCTION AND INDUSTRIAL EQUIPMENT
SAE-J285-1992 GASOLINE DISPENSER NOZZLE SPOUTS
SAE-J286-2006 SAE NO. 2 CLUTCH FRICTION TEST MACHINE GUIDELINES
SAE-J287-1980 DRIVER HAND CONTROL REACH
SAE-J288-2002 (R) SNOWMOBILE FUEL TANKS
SAE-J291-1980 DETERMINATION OF BRAKE FLUID TEMPERATURE - JUNE 1980
SAE-J292-1973 SNOWMOBILE AND SNOWMOBILE CUTTER LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT
SAE-J293-2004 (R) TRUCK AND BUS GRADE PARKING PERFORMANCE REQUIREMENTS
SAE-J294-2004 SERVICE BRAKE STRUCTURAL INTEGRITY TEST PROCEDUREVEHICLES OVER 4500 KG (10 000 LB) GVWR
SAE-J297-1980 OPERATOR CONTROLS ON INDUSTRIAL EQUIPMENT
SAE-J299-1980 STOPPING DISTANCE TEST PROCEDURE
SAE-J3000-2003 THERMOPLASTIC ELASTOMER CLASSIFICATION SYSTEM
SAE-J300-2004 ENGINE OIL VISCOSITY CLASSIFICATION
SAE-J301-1987 EFFECTIVE DATES OF NEW OR REVISED TECHNICAL REPORTS
SAE-J30-1998 FUEL AND OIL HOSES - FSC 4720
SAE-J304-1999 ENGINE OIL TESTS
SAE-J306-2005 AUTOMOTIVE GEAR LUBRICANT VISCOSITY CLASSIFICATION
SAE-J308-1996 (R) AXLE AND MANUAL TRANSMISSION LUBRICANTS - JANUARY 1996
SAE-J310-2005 AUTOMOTIVE LUBRICATING GREASES
SAE-J311-2000 FLUID FOR PASSENGER CAR TYPE AUTOMATIC TRANSMISSIONS
SAE-J31-1986 HYDRAULIC BACKHOE LIFT CAPACITY - MARCH 1986
SAE-J312-2001 AUTOMOTIVE GASOLINES - FEBRUARY 2001
SAE-J313-2004 DIESEL FUELS
SAE-J314-2002 FELTS - WOOL AND PART WOOL
SAE-J315-2004 FIBERBOARD TEST PROCEDURE
SAE-J318-1997 AUTOMOTIVE AIR BRAKE LINE COUPLERS (GLADHANDS)
SAE-J321-1999 (R) TIRE GUARDS FOR OPERATOR PROTECTION - EARTHMOVING HAULAGE MACHINES
SAE-J322-2003 NONMETALLIC TRIM MATERIALSTEST METHOD FOR DETERMINING THE STAINING RESISTANCE TO HYDROGEN SULFIDE GAS
SAE-J323-2004 TEST METHOD FOR DETERMINING COLD CRACKING OF FLEXIBLE PLASTIC MATERIALS
SAE-J326-1986 NOMENCLATURE-HYDRAULIC BACKHOES - MARCH 1986
SAE-J328-2005 WHEELSPASSENGER CAR AND LIGHT TRUCK PERFORMANCE REQUIREMENTS AND TEST PROCEDURES
SAE-J331-1987 SOUND LEVELS FOR MOTORCYCLES
SAE-J33-1991 SNOWMOBILE DEFINITIONS AND NOMENCLATURE - GENERAL
SAE-J332-2002 TESTING MACHINES FOR MEASURING THE UNIFORMITY OF PASSENGER CAR AND LIGHT TRUCK TIRES
SAE-J335-1995 (R) MULTIPOSITION SMALL ENGINE EXHAUST SYSTEM FIRE IGNITION SUPPRESSION - JUNE 1995
SAE-J336-1988 SOUND LEVEL FOR TRUCK CAB INTERIOR
SAE-J339-1994 (R) SEAT BELT HARDWARE WEBBING ABRASION TEST PROCEDURE - JUNE 1994
SAE-J34-2005 EXTERIOR SOUND LEVEL MEASUREMENT PROCEDURE FOR PLEASURE MOTORBOATS
SAE-J342-1991 SPARK ARRESTER TEST PROCEDURE FOR LARGE SIZE ENGINES - JANUARY 1991
SAE-J343-2004 TEST AND TEST PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES
SAE-J345A-1969 WET OR DRY PAVEMENT PASSENGER CAR TIRE PEAK AND LOCKED WHEEL BRAKING TRACTION - MARCH 1969
SAE-J347-1995 DIESEL FUEL INJECTOR ASSEMBLY TYPE 7 (9.5 MM)
SAE-J348-1990 (R) WHEEL CHOCKS - JUNE 1990
SAE-J349-1991 DETECTION OF SURFACE IMPERFECTIONS IN FERROUS RODS, BARS, TUBES, AND WIRES - FEBRUARY 1991
SAE-J350-1991 SPARK ARRESTER TEST PROCEDURE FOR MEDIUM SIZE ENGINES - JANUARY 1991
SAE-J356-1999 (R) WELDED FLASH-CONTROLLED LOW-CARBON STEEL TUBING NORMALIZED FOR BENDING, DOUBLE FLARING, AND BEADING
SAE-J357-1999 PHYSICAL AND CHEMICAL PROPERTIES OF ENGINE OILS
SAE-J358-1991 NONDESTRUCTIVE TESTS - FEBRUARY 1991
SAE-J359-1991 INFRARED TESTING - FEBRUARY 1991
SAE-J360-2001 (R) TRUCK AND BUS GRADE PARKING PERFORMANCE TEST PROCEDURE
SAE-J361-2003 (R) PROCEDURE FOR VISUAL EVALUATION OF INTERIOR AND EXTERIOR AUTOMOTIVE TRIM
SAE-J363-1987 FILTER-BASE MOUNTING
SAE-J365-2004 METHOD OF TESTING RESISTANCE TO SCUFFING OF TRIM MATERIALS
SAE-J366-1987 EXTERIOR SOUND LEVEL FOR HEAVY TRUCKS AND BUSES
SAE-J369-2003 (R) FLAMMABILITY OF POLYMERIC INTERIOR MATERIALS HORIZONTAL TEST METHOD
SAE-J371-1985 DRAIN, FILL AND LEVEL PLUGS FOR OFF-ROAD, SELF-PROPELLED WORK MACHINES
SAE-J373-1978 HOUSING INTERNAL DIMENSIONS FOR SINGLE- AND TWO-PLATE SPRING-LOADED CLUTCHES
SAE-J374-2002 VEHICLE ROOF STRENGTH TEST PROCEDURE
SAE-J375-1985 RADIUS-OF-LOAD OR BOOM ANGLE INDICATING SYSTEMS
SAE-J376-1985 LOAD INDICATING DEVICES IN LIFTING CRANE SERVICE - APRIL 1985
SAE-J377-2001 (R) VEHICULAR TRAFFIC SOUND SIGNALING DEVICES
SAE-J378-2004 (R) MARINE PROPULSION SYSTEM WIRING
SAE-J379-2004 (R) GOGAN HARDNESS OF BRAKE LINING
SAE-J380-2002 (R) SPECIFIC GRAVITY OF FRICTION MATERIAL
SAE-J381-2000 (R) WINDSHIELD DEFROSTING SYSTEMS TEST PROCEDURE AND PERFORMANCE REQUIREMENTS - TRUCKS, BUSES, AND MULTIPURPOSE

VEHICLES
SAE-J38-1991 (R) LIFT ARM SUPPORT DEVICES FOR LOADERS
SAE-J383-1995 (R) MOTOR VEHICLE SEAT BELT ANCHORAGES - DESIGN RECOMMENDATIONS - JUNE 1995
SAE-J384-1994 (R) MOTOR VEHICLE SEAT BELT ANCHORAGES - TEST PROCEDURE - JUNE 1994
SAE-J385-1995 MOTOR VEHICLE SEAT BELT ANCHORAGES - PERFORMANCE REQUIREMENTS - MARCH 1995
SAE-J386-2006 (R) OPERATOR RESTRAINT SYSTEM FOR OFF-ROAD WORK MACHINES
SAE-J387-1995 (R) TERMINOLOGY - MOTOR VEHICLE LIGHTING - SEPTEMBER 1995
SAE-J390-1999 (R) DUAL DIMENSIONING ENGINEERING DRAWINGS
SAE-J391-1969 DEFINITION FOR PARTICLE SIZE
SAE-J392-2003 MOTORCYCLE AND MOTOR DRIVEN CYCLE ELECTRICAL SYSTEM MAINTENANCE OF DESIGN VOLTAGE
SAE-J393-2001 (R) NOMENCLATURE - WHEELS, HUBS, AND RIMS FOR COMMERCIAL VEHICLES
SAE-J397-1995 DEFLECTION LIMITING VOLUMEPROTECTIVE STRUCTURES LABORATORY EVALUATION
SAE-J398-2005 (R) RATED (ADVERTISED) FUEL CAPACITYPASSENGER CAR, MULTI-PURPOSE PASSENGER VEHICLES, AND LIGHT DUTY TRUCKS
SAE-J399-1976 ANODIZED ALUMINUM AUTOMOTIVE PARTS
SAE-J4000-1999 IDENTIFICATION AND MEASUREMENT OF BEST PRACTICE IN IMPLEMENTATION OF LEAN OPERATION
SAE-J4001-1999 IMPLEMENTATION OF LEAN OPERATION USER MANUAL
SAE-J400-2002 TEST FOR CHIP RESISTANCE OF SURFACE COATINGS
SAE-J4002-2005 (R) H-POINT MACHINE (HPM-II) SPECIFICATIONS AND PROCEDURE FOR H-POINT DETERMINATIONAUDITING VEHICLE SEATS
SAE-J4003-2005 H-POINT MACHINE (HPM-II)PROCEDURE FOR H-POINT DETERMINATIONBENCHMARKING VEHICLE SEATS
SAE-J4004-2005 POSITIONING THE H-POINT DESIGN TOOL SEATING REFERENCE POINT AND SEAT TRACK LENGTH
SAE-J401-2000 SELECTION AND USE OF STEELS
SAE-J402-2005 (R) NEW STEEL DESIGNATION SYSTEM FOR WROUGHT OR ROLLED STEEL
SAE-J403-2001 CHEMICAL COMPOSITIONS OF SAE CARBON STEELS - SUPERSEDES FORD ESN-M1A46-A
SAE-J404-2000 CHEMICAL COMPOSITIONS OF SAE ALLOY STEELS
SAE-J405-1998 (R) CHEMICAL COMPOSITIONS OF SAE WROUGHT STAINLESS STEELS
SAE-J406-1998 METHODS OF DETERMINING HARDENABILITY OF STEELS
SAE-J409-1990 PRODUCT ANALYSIS - PERMISSIBLE VARIATIONS FROM SPECIFIED CHEMICAL ANALYSIS OF A HEAT OR CAST OF STEEL
SAE-J411-1997 (R) CARBON AND ALLOY STEELS
SAE-J412-1995 GENERAL CHARACTERISTICS AND HEAT TREATMENTS OF STEELS - OCTOBER 1995
SAE-J413-1932 MECHANICAL PROPERTIES OF HEAT TREATED WROUGHT STEELS
SAE-J415-1995 (R) DEFINITION OF HEAT TREATING TERMS - JULY 1995
SAE-J417-1983 HARDNESS TESTS AND HARDNESS NUMBER CONVERSIONS - DECEMBER 1983
SAE-J419-1983 METHODS OF MEASURING DECARBURIZATION - DECEMBER 1983
SAE-J420-1991 MAGNETIC PARTICLE INSPECTION - MARCH 1991
SAE-J422-1983 MICROSCOPIC DETERMINATION OF INCLUSIONS IN STEELS - DECEMBER 1983
SAE-J423-1983 METHODS OF MEASURING CASE DEPTH
SAE-J425-1991 ELECTROMAGNETIC TESTING BY EDDY CURRENT METHODS - MARCH 1991
SAE-J426-1991 LIQUID PENETRANT TEST METHODS - MARCH 1991
SAE-J427-1991 PENETRATING RADIATION INSPECTION - MARCH 1991
SAE-J428-1991 ULTRASONIC INSPECTION - MARCH 1991
SAE-J429-1999 MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
SAE-J430-1960 MECHANICAL AND CHEMICAL REQUIREMENTS FOR NONTHREADED FASTENERS CARBON STEEL SOLID RIVETS - REPLACES FORD ESA-

M1A14-A
SAE-J431-2000 (R) AUTOMOTIVE GRAY IRON CASTINGS
SAE-J434-2004 (R) AUTOMOTIVE DUCTILE (NODULAR) IRON CASTINGS
SAE-J435-2002 (R) AUTOMOTIVE STEEL CASTINGS
SAE-J437A-1970 SELECTION AND HEAT TREATMENT OF TOOL AND DIE STEELS
SAE-J438B-1970 TOOL AND DIE STEELS - MAY 1970
SAE-J439A-1977 SINTERED CARBIDE TOOLS - FEBRUARY 1977
SAE-J441-1993 (R) CUT WIRE SHOT - JUNE 1993
SAE-J44-2003 SERVICE BRAKE SYSTEM PERFORMANCE REQUIREMENTSSNOWMOBILES
SAE-J442-2006 TEST STRIP, HOLDER, AND GAGE FOR SHOT PEENING
SAE-J443-2003 (R) PROCEDURES FOR USING STANDARD SHOT PEENING TEST STRIP
SAE-J444-1993 CAST SHOT AND GRIT SIZE SPECIFICATIONS FOR PEENING AND CLEANING
SAE-J445-1996 METALLIC SHOT AND GRIT MECHANICAL TESTING
SAE-J447-1995 (R) PREVENTION OF CORROSION OF MOTOR VEHICLE BODY AND CHASSIS COMPONENTS - JULY 1995
SAE-J448A-1963 SURFACE TEXTURE - JUNE 1963
SAE-J449A-1963 SURFACE TEXTURE CONTROL - JUNE 1963
SAE-J450-1960 USE OF TERMS YIELD STRENGTH AND YIELD POINT
SAE-J451-1976 ALUMINUM ALLOYS - FUNDAMENTALS - MARCH 1976
SAE-J45-2003 BRAKE SYSTEM TEST PROCEDURE-SNOWMOBILES
SAE-J452-2003 GENERAL INFORMATION - CHEMICAL COMPOSITIONS, MECHANICAL AND PHYSICAL PROPERTIES OF SAE ALUMINUM CASTING ALLOYS
SAE-J454-1991 GENERAL DATA ON WROUGHT ALUMINUM ALLOYS - FEBRUARY 1991
SAE-J457-1991 CHEMICAL COMPOSITIONS, MECHANICAL PROPERTY LIMITS, AND DIMENSIONAL TOLERANCES OF SAE WROUGHT ALUMINUM ALLOYS -

FEBRUARY 1991
SAE-J459-1991 BEARING AND BUSHING ALLOYS - OCTOBER 1991
SAE-J460-1991 BEARING BUSHING ALLOYS CHEMICAL COMPOSITION OF SAE BEARING AND BUSHING ALLOYS
SAE-J461-1981 WROUGHT AND CAST COPPER ALLOYS
SAE-J46-1973 WHEEL-SLIP BRAKE-CONTROL SYSTEM ROAD TEST CODE
SAE-J462-1976 CAST COPPER ALLOYS
SAE-J463-1981 WROUGHT COPPER AND COPPER ALLOYS      
SAE-J464-1979 MAGNESIUM ALLOYS - APRIL 1979
SAE-J465-1983 MAGNESIUM CASTING ALLOYS - JUNE 1983
SAE-J466-1979 MAGNESIUM WROUGHT ALLOYS - APRIL 1979
SAE-J467B-1968 SPECIAL PURPOSE ALLOYS ("SUPERALLOYS") - OCTOBER 1968
SAE-J468-1988 ZINC ALLOY INGOT AND DIE CASTING COMPOSITIONS - DECEMBER 1988
SAE-J469-1983 ZINC DIE CASTING ALLOYS
SAE-J470C-1976 WROUGHT NICKEL AND NICKEL-RELATED ALLOYS - JULY 1976
SAE-J471D-1973 SINTERED POWDER METAL PARTS: FERROUS - AUGUST 1973
SAE-J47-2005 MAXIMUM SOUND LEVEL POTENTIAL FOR MOTORCYCLES
SAE-J473A-1962 SOLDERS - JUNE 1962
SAE-J474-1972 ELECTROPLATING AND RELATED FINISHES
SAE-J476A-1961 DRYSEAL PIPE THREADS - JUNE 1961
SAE-J48-1983 GUIDELINES FOR LIQUID LEVEL INDICATORS
SAE-J482-2006 HEXAGON HIGH NUTS
SAE-J483-2006 HIGH AND LOW CROWN (BLIND, ACORN) HEX NUTS
SAE-J485-1995 HOLES IN BOLT AND SCREW SHANKS AND SLOTS IN NUTS FOR COTTER PINS
SAE-J490-1996 (R) BALL JOINTS - SEPTEMBER 1996
SAE-J491-1987 STEERING BALL STUDS AND SOCKET ASSEMBLIES - NOVEMBER 1987
SAE-J49-1980 SPECIFICATION DEFINITIONS - HYDRAULIC BACKHOES - APRIL 1980
SAE-J492-2005 (R) GUIDE FOR RIVET SELECTION AND DESIGN CONSIDERATION
SAE-J493-1961 ROD ENDS AND CLEVIS PINS - JUNE 1961
SAE-J499A-1975 PARALLEL SIDE SPLINES FOR SOFT BROACHED HOLES IN FITTINGS - OCTOBER 1975
SAE-J501-1948 SHAFT ENDS - MAY 1948
SAE-J502-1972 WOODRUFF KEYS - SEPTEMBER 1972
SAE-J503-1959 WOODRUFF KEY SLOTS AND KEYWAYS - MAY 1959
SAE-J506-1978 SLEEVE TYPE HALF BEARINGS - NOVEMBER 1978
SAE-J510-1985 LEAF SPRINGS FOR MOTOR VEHICLE SUSPENSION - MADE TO CUSTOMARY U.S. UNITS
SAE-J511-1970 PNEUMATIC SPRING TERMINOLOGY
SAE-J51-2004 REFRIGERANT 12 AUTOMOTIVE AIR-CONDITIONING HOSE
SAE-J512-1997 AUTOMOTIVE TUBE FITTINGS
SAE-J513-1999 REFRIGERATION TUBE FITTINGS - GENERAL SPECIFICATIONS
SAE-J514-2004 HYDRAULIC TUBE FITTINGS
SAE-J515-2001 SPECIFICATION FOR HYDRAULIC O-RING MATERIALS, PROPERTIES, AND SIZES FOR METRIC AND INCH STUD ENDS, FACE SEAL

FITTING AND FOUR-SCREW FLANGE TUBE CONNECTIONS
SAE-J516-2005 (R) HYDRAULIC HOSE FITTINGS
SAE-J517-2006 HYDRAULIC HOSE
SAE-J518-1993 HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, FOUR-BOLT SPLIT FLANGE TYPE - JUNE 1993
SAE-J524-1996 (R) SEAMLESS LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING - FEBRUARY 1996
SAE-J525-1999 (R) WELDED AND COLD DRAWN LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING
SAE-J526-2000 WELDED LOW-CARBON STEEL TUBING - FSC 4710
SAE-J527-2000 (R) BRAZED DOUBLE WALL LOW-CARBON STEEL TUBING
SAE-J528-1991 SEAMLESS COPPER TUBE - JUNE 1991
SAE-J530-1995 AUTOMOTIVE PIPE FITTINGS - MAY 1995
SAE-J531-1995 AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS - MAY 1995
SAE-J532-1993 (R) AUTOMOTIVE STRAIGHT THREAD FILLER AND DRAIN PLUGS - JUNE 1993
SAE-J533-1999 FLARES FOR TUBING
SAE-J534-1998 LUBRICATION FITTINGS
SAE-J537-2000 (R) STORAGE BATTERIES
SAE-J539-1993 VOLTAGES FOR DIESEL ELECTRICAL SYSTEMS - NOVEMBER 1993
SAE-J541-1996 (R) VOLTAGE DROP FOR STARTING MOTOR CIRCUITS - OCTOBER 1996
SAE-J542-1991 STARTING MOTOR MOUNTINGS - JUNE 1991
SAE-J543-1995 (R) STARTING MOTOR PINIONS AND RING GEARS - NOVEMBER 1995
SAE-J544-1996 (R) ELECTRIC STARTING MOTOR TEST PROCEDURE
SAE-J548-1-2000 (R) SPARK PLUGS
SAE-J548-2-2000 SPARK PLUG INSTALLATION SOCKETS
SAE-J549-1999 PREIGNITION RATING OF SPARK PLUGS
SAE-J551-11-2000 VEHICLE ELECTROMAGNETIC IMMUNITY - OFF-VEHICLE SOURCE
SAE-J551-1-2002 (R) PERFORMANCE LEVELS AND METHODS OF MEASUREMENT OF ELECTROMAGNETIC COMPATIBILITY OF VEHICLES, BOATS (UP TO

15 M), AND MACHINES (50 HZ TO 18 GHZ)
SAE-J551-12-1996 VEHICLE ELECTROMAGNETIC IMMUNITY - ON-BOARD TRANSMITTER SIMULATION
SAE-J551-13-2003 (R) VEHICLE ELECTROMAGNETIC IMMUNITY - BULK CURRENT INJECTION
SAE-J551-15-2002 (R) VEHICLE ELECTROMAGNETIC IMMUNITY - ELECTROSTATIC DISCHARGE (ESD)
SAE-J551-16-2005 ELECTROMAGNETIC IMMUNITYOFF-VEHICLE SOURCE (REVERBERATION CHAMBER METHOD) PART 16IMMUNITY TO RADIATED

ELECTROMAGNETIC FIELDS
SAE-J551-17-2003 (R) VEHICLE ELECTROMAGNETIC IMMUNITY - POWER LINE MAGNETIC FIELDS
SAE-J551-2-1994 TEST LIMITS AND METHODS OF MEASUREMENT OF RADIO DISTURBANCE CHARACTERISTICS OF VEHICLES, MOTORBOATS, AND

SPARK-IGNITED ENGINE-DRIVEN DEVICES - MARCH 1994
SAE-J551-4-1994 TEST LIMITS AND METHODS OF MEASUREMENT OF RADIO DISTURBANCE CHARACTERISTICS OF VEHICLES AND DEVICES,

BROADBAND AND NARROWBAND, 150 KHZ TO 1000 MHZ
SAE-J551-5-2004 PERFORMANCE LEVELS AND METHODS OF MEASUREMENT OF MAGNETIC AND ELECTRIC FIELD STRENGTH FROM ELECTRIC VEHICLES,

BROADBAND, 9 KHZ TO 30 MHZ
SAE-J553-2004 CIRCUIT BREAKERS
SAE-J554-1987 ELECTRIC FUSES (CARTRIDGE TYPE) - AUGUST 1987
SAE-J560-2004 (R) PRIMARY AND AUXILIARY SEVEN CONDUCTOR ELECTRICAL CONNECTOR FOR TRUCK-TRAILER JUMPER CABLE
SAE-J561-1993 ELECTRICAL TERMINALS - EYELET AND SPADE TYPE
SAE-J56-1999 (R) ROAD VEHICLES - ALTERNATORS WITH REGULATORS - TEST METHODS AND GENERAL REQUIREMENTS
SAE-J563-1978 SIX- AND TWELVE-VOLT CIGAR LIGHTER RECEPTACLES
SAE-J564-1990 HEADLAMP BEAM SWITCHING - MARCH 1990
SAE-J565-1989 SEMIAUTOMATIC HEADLAMP BEAM SWITCHING DEVICES - JUNE 1989
SAE-J567-1998 (R) LAMP BULB RETENTION SYSTEM
SAE-J57-1994 SOUND LEVEL OF HIGHWAY TRUCK TIRES
SAE-J572-1998 REQUIREMENTS FOR SEALED LIGHTING UNIT FOR CONSTRUCTION AND INDUSTRIAL MACHINES
SAE-J573-1998 (R) MINIATURE LAMP BULBS
SAE-J575-2006 (R) TEST METHODS AND EQUIPMENT FOR LIGHTING DEVICES AND COMPONENTS FOR USE ON VEHICLES LESS THAN 2032 MM IN

OVERALL WIDTH
SAE-J576-1991 (R) PLASTIC MATERIALS FOR USE IN OPTICAL PARTS SUCH AS LENSES AND REFLEX REFLECTORS OF MOTOR VEHICLE LIGHTING

DEVICES
SAE-J577-2005 VIBRATION TEST MACHINE AND OPERATION PROCEDURE
SAE-J578-2002 (R) COLOR SPECIFICATION
SAE-J581-2004 AUXILIARY UPPER BEAM LAMPS
SAE-J58-1993 FLANGED 12-POINT SCREWS
SAE-J583-2005 (R) FRONT FOG LAMP - : 2006
SAE-J584-2003 MOTORCYCLE HEADLAMPS
SAE-J585-2000 (R) TAIL LAMPS (REAR POSITION LAMPS) FOR USE ON MOTOR VEHICLES LESS THAN 2032 MM IN OVERALL WIDTH
SAE-J586-2000 STOP LAMPS FOR USE ON MOTOR VEHICLES LESS THAN 2032 MM IN OVERALL WIDTH
SAE-J587-2003 LICENSE PLATE ILLUMINATION DEVICES (REAR REGISTRATION PLATE ILLUMINATION DEVICES)
SAE-J588-2000 TURN SIGNAL LAMPS FOR USE ON MOTOR VEHICLES LESS THAN 2032 MM IN OVERALL WIDTH
SAE-J589B-1977 TURN SIGNAL SWITCH - OCTOBER 1977
SAE-J591-2003 SPOT LAMPS
SAE-J592-2000 SIDEMARKER LAMPS FOR USE ON ROAD VEHICLES LESS THAN 2032 MM IN OVERALL WIDTH
SAE-J593-2005 BACKUP LAMPS (REVERSING LAMPS)
SAE-J594-1995 REFLEX REFLECTORS
SAE-J595-2005 (R) DIRECTIONAL FLASHING OPTICAL WARNING DEVICES FOR AUTHORIZED EMERGENCY, MAINTENANCE, AND SERVICE VEHICLES
SAE-J599-1997 (R) LIGHTING INSPECTION CODE
SAE-J600-1993 (R) HEADLAMP AIM TEST MACHINES - FEBRUARY 1993
SAE-J602-1989 HEADLAMP AIMING DEVICE FOR MECHANICALLY AIMABLE HEADLAMP UNITS - DECEMBER 1989
SAE-J604-1958 ENGINE TERMINOLOGY AND NOMENCLATURE - GENERAL
SAE-J609-2003 (R) MOUNTING FLANGES AND POWER TAKE-OFF SHAFTS FOR SMALL ENGINES
SAE-J614-1995 ENGINE AND TRANSMISSION DIPSTICK MARKING
SAE-J615-1991 ENGINE MOUNTINGS
SAE-J616-1990 ENGINE FOOT MOUNTING (FRONT AND REAR)
SAE-J617-1992 (R) ENGINE FLYWHEEL HOUSING AND MATING TRANSMISSION HOUSING FLANGES
SAE-J618-1991 FLYWHEELS FOR SINGLE-PLATE SPRING-LOADED CLUTCHES - JANUARY 1991
SAE-J619-1993 FLYWHEELS FOR TWO-PLATE SPRING-LOADED CLUTCHES - DECEMBER 1993
SAE-J620-1988 FLYWHEELS FOR INDUSTRIAL ENGINES USED WITH INDUSTRIAL POWER TAKE-OFFS EQUIPPED WITH DRIVING-RING TYPE

OVERCENTER CLUTCHES AND ENGINE-MOUNTED MARINE GEARS AND SINGLE BEARING ENGINE-MOUNTED POWER GENERATORS
SAE-J621-1989 INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING-TYPE OVERCENTER CLUTCHES - APRIL 1989
SAE-J626-1988 DIESEL FUEL INJECTION - END-MOUNTING FLANGES FOR FUEL INJECTION PUMPS
SAE-J629-1991 DIESEL FUEL INJECTOR ASSEMBLY - FLANGE MOUNTED TYPES 5 AND 6
SAE-J631-1998 (R) RADIATOR NOMENCLATURE
SAE-J635-1984 FAN HUB BOLT CIRCLES AND PILOT HOLES
SAE-J636-1992 V-BELTS AND PULLEYS
SAE-J637-1997 AUTOMOTIVE V-BELT DRIVES
SAE-J638-1982 MOTOR VEHICLE HEATER TEST PROCEDURE
SAE-J639-2005 (R) SAFETY STANDARDS FOR MOTOR VEHICLE REFRIGERANT VAPOR COMPRESSSIONS SYSTEMS
SAE-J640-2000 SYMBOLS FOR HYDRODYNAMIC DRIVES
SAE-J641-1993 HYDRODYNAMIC DRIVES TERMINOLOGY
SAE-J64-1988 VEHICLE IDENTIFICATION NUMBERS - SNOWMOBILES
SAE-J643-1989 HYDRODYNAMIC DRIVE TEST CODE
SAE-J645-1992 AUTOMOTIVE TRANSMISSION TERMINOLOGY
SAE-J646-1969 PLANETARY GEAR(S) - TERMINOLOGY - OCTOBER 1969
SAE-J647-1997 (R) TRANSMISSIONS - SCHEMATIC DIAGRAMS
SAE-J648-2000 AUTOMATIC TRANSMISSION HYDRAULIC CONTROL SYSTEMS - TERMINOLOGY
SAE-J649-1994 AUTOMATIC TRANSMISSION FUNCTIONS - TERMINOLOGY
SAE-J651-2005 PASSENGER CAR AND LIGHT TRUCK AUTOMATIC TRANSMISSION AND AUTOMATIC TRANSAXLE TEST CODE
SAE-J656-1988 AUTOMOTIVE BRAKE DEFINITIONS AND NOMENCLATURE - APRIL 1988
SAE-J661-1997 (R) BRAKE LINING QUALITY TEST PROCEDURE
SAE-J662-1990 BRAKE BLOCK CHAMFER
SAE-J663-2001 RIVETS FOR BRAKE LININGS AND BOLTS FOR BRAKE BLOCKS
SAE-J670E-1976 VEHICLE DYNAMICS TERMINOLOGY, RECOMMENDED PRACTICE
SAE-J671-1997 (R) VIBRATION DAMPING MATERIALS AND UNDERBODY COATINGS
SAE-J67-1972 SHOVEL DIPPER, CLAM BUCKET, AND DRAGLINE BUCKET RATING
SAE-J673-2005 (R) AUTOMOTIVE SAFETY GLASSES
SAE-J674-2005 (R) SAFETY GLAZING MATERIALS - MOTOR VEHICLES AND MOTOR VEHICLE EQUIPMENT
SAE-J678-1984 SPEEDOMETERS AND TACHOMETERS - AUTOMOTIVE, RECOMMENDED PRACTICE
SAE-J680-1988 LOCATION AND OPERATION OF INSTRUMENTS AND CONTROLS IN MOTOR TRUCK CABS, RECOMMENDED PRACTICE
SAE-J68-2004 TESTS FOR SNOWMOBILE SWITCHING DEVICES AND COMPONENTS
SAE-J682-2003 REAR WHEEL SPLASH AND STONE THROW PROTECTION
SAE-J683-1985 TIRE CHAIN CLEARANCE- TRUCKS, BUSES (EXCEPT SUBURBAN, INTERCITY, AND TRANSIT BUSES), AND COMBINATIONS OF

VEHICLES, INFORMATION REPORT - AUGUST 1985
SAE-J684-2005 TRAILER COUPLINGS, HITCHES, AND SAFETY CHAINSAUTOMOTIVE TYPE
SAE-J686-1999 MOTOR VEHICLE LICENSE PLATES
SAE-J689-1996 (R) CURBSTONE CLEARANCE, APPROACH, DEPARTURE, AND RAMP BREAKOVER ANGLES - PASSENGER CAR AND LIGHT TRUCK,

RECOMMENDED PRACTICE - JUNE 1996
SAE-J691-1990 MOTOR TRUCK CA DIMENSIONS, RECOMMENDED PRACTICE - SEPTEMBER 1990
SAE-J693-1989 TRUCK OVERALL WIDTHS ACROSS DUAL TIRES, INFORMATION REPORT - APRIL 1989
SAE-J694-2001 DISC WHEEL/HUB OR DRUM INTERFACE DIMENSIONS - COMMERCIAL VEHICLES
SAE-J695-1989 TURNING ABILITY AND OFF TRACKING - MOTOR VEHICLES
SAE-J697-1988 SAFETY CHAIN OF FULL TRAILERS OR CONVERTER DOLLIES, RECOMMENDED PRACTICE - MAY 1988
SAE-J699-1985 AVERAGE VEHICLE DIMENSIONS FOR USE IN DESIGNING DOCKING FACILITIES FOR MOTOR VEHICLES, RECOMMENDED PRACTICE -

NOVEMBER 1985
SAE-J700-1985 UPPER COUPLER KINGPIN - COMMERCIAL TRAILERS AND SEMITRAILERS
SAE-J701-1984 TRUCK TRACTOR SEMITRAILER INTERCHANGE COUPLING DIMENSIONS, INFORMATION REPORT - AUGUST 1984
SAE-J702-2003 (R) BRAKE AND ELECTRICAL CONNECTION LOCATIONS - TRUCK-TRACTOR AND TRUCK-TRAILER
SAE-J703-1954 FUEL SYSTEMS - TRUCK AND TRUCK TRACTORS
SAE-J704-1992 OPENINGS FOR SIX- AND EIGHT-BOLT TRUCK TRANSMISSION MOUNTED POWER TAKE-OFFS
SAE-J706-2003 RATING OF WINCHES
SAE-J709-1977 AGRICULTURAL TRACTOR TIRE LOADINGS, TORQUE FACTORS, AND INFLATION PRESSURES, STANDARD; - MAY 1977 (ASAE

S295.2); FORMERLY REFERRED TO AS J709D
SAE-J711-1991 TIRE SELECTION TABLES FOR AGRICULTURAL TRACTORS OF FUTURE DESIGN, RECOMMENDED PRACTICE - MARCH 1991 (ASAE

S220.4)
SAE-J712-1949 INDUSTRIAL AND AGRICULTURAL DISC WHEELS
SAE-J714-1986 WHEEL MOUNTING ELEMENTS FOR INDUSTRIAL AND AGRICULTURAL DISC WHEELS, RECOMMENDED PRACTICE - (ASAE S218.2)
SAE-J731-1985 COMPONENT NOMENCLATURE- LOADER, STANDARD;
SAE-J732-1992 (R) SPECIFICATION DEFINITIONS - LOADERS
SAE-J737-1989 HOLE SPACING FOR SCRAPER AND DOZER CUTTING EDGES
SAE-J738-1986 CUTTING EDGE-DOUBLE BEVEL CROSS SECTIONS, STANDARD - JUNE 1986
SAE-J739-1991 CUTTING EDGECURVED GRADER
SAE-J740-1986 COUNTERSUNK SQUARE HOLES FOR CUTTING EDGES AND END BITS
SAE-J744-1996 HYDRAULIC PUMP AND MOTOR MOUNTING AND DRIVE DIMENSIONS, STANDARD - JUNE 1996
SAE-J745-1987 HYDRAULIC POWER PUMP TEST PROCEDURE, RECOMMENDED PRACTICE - SUPERSEDES NFPA T3.9.20
SAE-J746-1955 HYDRAULIC MOTOR TEST PROCEDURES, RECOMMENDED PRACTICE - DECEMBER 1955
SAE-J747-1990 CONTROL VALVE TEST PROCEDURE, STANDARD - MAY 1990
SAE-J748-1957 HYDRAULIC DIRECTIONAL CONTROL VALVES, 3000 PSI MAXIMUM, RECOMMENDED PRACTICE
SAE-J751-1997 (R) OFF-ROAD TIRE AND RIM CLASSIFICATION - CONSTRUCTION MACHINES
SAE-J75-1999 MOTOR VEHICLE BRAKE FLUID CONTAINER COMPATIBILITY
SAE-J753-1991 MAINTENANCE INTERVAL CHART
SAE-J754A-1972 LUBRICANT TYPES - CONSTRUCTION AND INDUSTRIAL MACHINERY, INFORMATION REPORT - JANUARY 1972
SAE-J755-1950 MARINE PROPELLER-SHAFT ENDS AND HUBS, STANDARD;
SAE-J759-2001 (R) LIGHTING IDENTIFICATION CODE
SAE-J760-1999 DIMENSIONAL SPECIFICATIONS FOR GENERAL SERVICE SEALED LIGHTING UNITS
SAE-J764-1995 LOADING ABILITY TEST PROCEDURESCRAPERS
SAE-J765-1990 CRANE LOAD STABILITY TEST CODE - OCTOBER 1990
SAE-J771-1986 AUTOMOTIVE PRINTED CIRCUITS, STANDARD - APRIL 1986
SAE-J772-2004 CLEARANCE ENVELOPES FOR SIX-BOLT, EIGHT-BOLT, AND REAR TRUCK TRANSMISSION MOUNTED POWER TAKEOFFS
SAE-J773-1976 CONICAL SPRING WASHERS
SAE-J774-2000 (R) EMERGENCY WARNING DEVICE AND EMERGENCY WARNING DEVICE PROTECTIVE CONTAINER
SAE-J775-2004 (R) ENGINE POPPET VALVE INFORMATION REPORT
SAE-J78-1998 STEEL SELF-DRILLING TAPPING SCREWS
SAE-J782B-1980 MOTOR VEHICLE SEATING MANUAL, RECOMMENDED PRACTICE
SAE-J79-1972 BRAKE DISC AND DRUM THERMOCOUPLE INSTALLATION
SAE-J792A-1968 SAE MANUAL ON BLAST CLEANING, INFORMATION REPORT - JUNE 1968
SAE-J800-1994 (R) MOTOR VEHICLE SEAT BELT ASSEMBLY INSTALLATION, RECOMMENDED PRACTICE - JUNE 1994
SAE-J80-2004 AUTOMOTIVE RUBBER MATS
SAE-J810-1996 (R) CLASSIFICATION OF COMMON SURFACE IMPERFECTIONS IN SHEET STEEL, INFORMATION REPORT - MARCH 1996
SAE-J811-1981 SURFACE ROLLING AND OTHER METHODS FOR MECHANICAL PRESTRESSING OF METALS, INFORMATION REPORT; - AUGUST 1981
SAE-J81-1997 THREAD ROLLING SCREWS
SAE-J814-1999 ENGINE COOLANTS
SAE-J815-2002 LOAD DEFLECTION TESTING OF URETHANE FOAMS FOR AUTOMOTIVE SEATING
SAE-J817-1-1991 ENGINEERING DESIGN SERVICEABILITY GUIDELINES - CONSTRUCTION AND INDUSTRIAL MACHINERY - SERVICEABILITY

DEFINITIONS - OFF-ROAD WORK MACHINES, INFORMATION REPORT - MARCH 1991
SAE-J817-2-1991 ENGINEERING DESIGN SERVICEABILITY GUIDELINES - CONSTRUCTION AND INDUSTRIAL MACHINERY - MAINTAINABILITY INDEX

- OFF-ROAD WORK MACHINES, INFORMATION REPORT - MARCH 1991
SAE-J818-1987 RATED OPERATING LOAD FOR LOADERS, STANDARD - MAY 1987
SAE-J819-1987 ENGINE COOLING SYSTEM FIELD TEST (AIR-TO-BOIL), STANDARD; - MARCH 1987; SUPERSEDED BY SAE J1393
SAE-J820-1980 CRANE HOIST LINE SPEED AND POWER TEST CODE
SAE-J82-1998 MECHANICAL AND QUALITY REQUIREMENTS FOR MACHINE SCREWS
SAE-J823-1994 FLASHER TEST, STANDARD - JANUARY 1994
SAE-J824-1962 ENGINE ROTATION AND CYLINDER NUMBERING, STANDARD;
SAE-J826-1995 (R) DEVICES FOR USE IN DEFINING AND MEASURING VEHICLE SEATING ACCOMMODATION, STANDARD
SAE-J827-1996 HIGH-CARBON CAST-STEEL SHOT
SAE-J829-2005 FUEL TANK FILLER CAP AND CAP RETAINER
SAE-J830-1999 FUEL INJECTION EQUIPMENT NOMENCLATURE