SAE-J1668-1993 DIESEL ENGINES - FUEL INJECTION PUMP TESTING
SAE-J1670-2005 TYPE "F" CLAMPS FOR PLUMBING APPLICATIONS
SAE-J1671-2006 OUTBOARD MOUNTED BRAKE DRUM/DISC WHEEL HUB INTERFACE DIMENSIONSTRUCK AND BUS
SAE-J167-1992 OVERHEAD PROTECTION FOR AGRICULTURAL TRACTORS TEST PROCEDURES AND PERFORMANCE REQUIREMENTS
SAE-J1673-1996 HIGH VOLTAGE AUTOMOTIVE WIRING ASSEMBLY DESIGN, RECOMMENDED PRACTICE - JULY 1996
SAE-J1674-1998 EARLY ACQUISITION AND PRESERVATION OF INFORMATION IN A MOTOR VEHICLE ACCIDENT
SAE-J1677-2004 (R) TESTS AND PROCEDURES FOR STEEL AND COPPER NICKEL TUBING
SAE-J1678-2004 LOW-VOLTAGE ULTRATHIN WALL PRIMARY CABLE
SAE-J1679-1994 PEEL STRENGTH OF SOFT TRIM ADHESIVES, RECOMMENDED PRACTICE - APRIL 1994
SAE-J1681-2000 (R) GASOLINE, ALCOHOL, AND DIESEL FUEL SURROGATES FOR MATERIAL TESTING
SAE-J1682-1993 VALVE GUIDE INFORMATION REPORT, INFORMATION REPORT - SEPTEMBER 1993
SAE-J1684-2005 TEST METHOD FOR EVALUATING THE ELECTROCHEMICAL RESISTANCE OF COOLANT SYSTEM HOSES AND MATERIALS
SAE-J1689-1994 HYDRAULIC POWER UNITS USED ON MACHINE TOOLS AND EQUIPMENT FOR THE AUTOMOTIVE INDUSTRY, STANDARD - NOVEMBER
1994
SAE-J1690-1996 FLASHERS, RECOMMENDED PRACTICE - 08 1996
SAE-J1691-1997 PLASTIC MOTOR VEHICLE SAFETY GLAZING - TOLERANCES AND FABRICATION DETAILS
SAE-J169-1985 DESIGN GUIDELINES FOR AIR CONDITIONING SYSTEMS FOR OFF-ROAD OPERATOR ENCLOSURES - MARCH 1985
SAE-J1692-1993 VALVE SEAT INSERT INFORMATION REPORT, INFORMATION REPORT - SUPERSEDES FORD ESE-M1A106-A, ESE-M1A122-A
SAE-J1693-1994 REMANUFACTURED HYDRAULIC MASTER CYLINDER FOR MOTOR VEHICLE BRAKES - GENERAL CHARACTERISTICS AND TEST
PROCEDURE, RECOMMENDED PRACTICE - JUNE 1994
SAE-J1694-1994 REMANUFACTURED HYDRAULIC MASTER CYLINDER FOR MOTOR VEHICLE BRAKES - PERFORMANCE REQUIREMENTS, RECOMMENDED
PRACTICE - JUNE 1994
SAE-J1696-1997 STANDARD FUEL FILTER TEST FLUID
SAE-J1697-2003 RECOMMENDED PRACTICES FOR DESIGN AND EVALUATION OF PASSENGER AND LIGHT TRUCK COOLANT HOSE CLAMPED JOINTS
SAE-J1698-1-2005 VEHICLE EVENT DATA INTERFACEOUTPUT DATA DEFINITION
SAE-J1698-2005 (R) VEHICLE EVENT DATA INTERFACEVEHICULAR OUTPUT DATA DEFINITION
SAE-J1698-2-2004 VEHICLE EVENT DATA INTERFACE VEHICULAR DATA EXTRACTION
SAE-J1699-1-2001 SAE J1850 VERIFICATION TEST PROCEDURES
SAE-J1699-2-1998 OBD-II RELATED SAE SPECIFICATION VERIFICATION TEST PROCEDURES
SAE-J1699-3-2006 OBD II COMPLIANCE TEST CASES
SAE-J1700-1994 SOFTENING POINT OF INTERIOR TRIM ADHESIVES, RECOMMENDED PRACTICE - APRIL 1994
SAE-J1701-1999 TORQUE-TENSION TIGHTENING FOR INCH SERIES FASTENERS
SAE-J1701M-1996 TORQUE-TENSION TIGHTENING FOR METRIC SERIES FASTENERS, INFORMATION REPORT - JULY 1996
SAE-J1702-1994 SELF-PROPELLED SWEEPERS SWEEP-ABILITY PERFORMANCE
SAE-J1703-2004 MOTOR VEHICLE BRAKE FLUID
SAE-J1704-2004 BORATE ESTER BASED BRAKE FLUIDS
SAE-J1705-1995 LOW WATER TOLERANT BRAKE FLUIDS, RECOMMENDED PRACTICE - MAY 1995
SAE-J1706-1995 (R) PRODUCTION, HANDLING AND DISPENSING OF SAE J1703 MOTOR VEHICLE BRAKE FLUIDS, RECOMMENDED PRACTICE - JUNE
1995
SAE-J1707-2002 SERVICE MAINTENANCE OF SAE J1703 AND J1704 BRAKE FLUIDS IN MOTOR VEHICLE BRAKE SYSTEMS
SAE-J1708-2004 SERIAL DATA COMMUNICATIONS BETWEEN MICROCOMPUTER SYSTEMS IN HEAVY-DUTY VEHICLE APPLICATIONS
SAE-J1709-1999 EUROPEAN BRAKE FLUID TECHNOLOGY
SAE-J1711-1999 RECOMMENDED PRACTICE FOR MEASURING THE EXHAUST EMISSIONS AND FUEL ECONOMY OF HYBRID-ELECTRIC VEHICLES
SAE-J1713-2004 STRUCTURAL TESTING OF PASSENGER CAR AND TRUCK DISC BRAKES
SAE-J1715-2000 ELECTRIC VEHICLE TERMINOLOGY
SAE-J1717-1994 INTERIOR AUTOMOTIVE PLASTIC PART TESTING, RECOMMENDED PRACTICE - JUNE 1994
SAE-J1718-1997 (R) MEASUREMENT OF HYDROGEN GAS EMISSION FROM BATTERY-POWERED PASSENGER CARS AND LIGHT TRUCKS DURING BATTERY
CHARGING
SAE-J17-2003 LATEX FOAM RUBBERS
SAE-J1723-1995 SUPERCHARGER TESTING STANDARD, STANDARD - AUGUST 1995
SAE-J1725-1995 STRUCTURAL MODIFICATION FOR PERSONALLY LICENSED VEHICLES TO MEET THE TRANSPORTATION NEEDS OF PERSONS WITH
DISABILITIES
SAE-J1726-2000 (R) AIR-TO-AIR CHARGE AIR COOLER (CAC) INTERNAL CLEANLINESS
SAE-J1727-1996 INJURY CALCULATIONS GUIDELINES, INFORMATION REPORT - AUGUST 1996
SAE-J1729-2001 (R) PARKING BRAKE DRAWBAR PULL TEST PROCEDURE - COMMERCIAL VEHICLE
SAE-J1730-2004 ABS EXCITOR RING LOCATION STANDARDIZATION
SAE-J1731-2001 PILOT BEARINGS FOR TRUCK AND BUS APPLICATIONS
SAE-J1732-1998 HFC-134A (R-134A) REFRIGERANT RECOVERY EQUIPMENT FOR MOBILE AUTOMOTIVE AIR-CONDITIONING SYSTEMS
SAE-J1733-1994 SIGN CONVENTION FOR VEHICLE CRASH TESTING, INFORMATION REPORT - DECEMBER 1994
SAE-J1735-1995 HARMONIZED VEHICLE HEADLAMP PERFORMANCE REQUIREMENTS, RECOMMENDED PRACTICE - JANUARY 1995
SAE-J1737-2004 TEST PROCEDURE TO DETERMINE THE HYDROCARBON LOSSES FROM FUEL TUBES, HOSES, FITTINGS, AND FUEL LINE ASSEMBLIES
BY RECIRCULATION
SAE-J1739-2002 (R) POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS
ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA), AND POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS FOR
MACHINERY (MACH
SAE-J1741-1999 DISCRIMINATING BACK-UP ALARM SYSTEM STANDARD
SAE-J174-1996 TORQUE-TENSION TEST PROCEDURE FOR STEEL THREADED FASTENERS - INCH SERIES
SAE-J1742-2005 (R) CONNECTIONS FOR HIGH VOLTAGE ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSES TEST METHODS AND GENERAL
PERFORMANCE REQUIREMENTS
SAE-J1744-1994 280 RELAY FOOTPRINT, STANDARD - JUNE 1994
SAE-J1746-1999 ISP-VEHICLE LOCATION REFERENCING STANDARD
SAE-J1747-1994 RECOMMENDED METHODS FOR CONDUCTING CORROSION TESTS IN GASOLINE/METHANOL FUEL MIXTURES, INFORMATION REPORT -
DECEMBER 1994
SAE-J1748-1998 METHODS FOR DETERMINING PHYSICAL PROPERTIES OF POLYMERIC MATERIALS EXPOSED TO GASOLINE/OXYGENATED FUEL
MIXTURES
SAE-J174M-1996 (R) TORQUE-TENSION TEST PROCEDURE FOR STEEL THREADED FASTENERS - METRIC SERIES
SAE-J1750-1995 DESCRIBING AND EVALUATING THE TRUCK DRIVER- VIEWING ENVIRONMENT, RECOMMENDED PRACTICE - MARCH 1995
SAE-J1751-1995 LUBRICATION COMPONENTS AND SYSTEMS USED ON MACHINE TOOLS AND EQUIPMENT FOR THE AUTOMOTIVE INDUSTRY,
RECOMMENDED PRACTICE - DECEMBER 1995
SAE-J175-1996 WHEELS - IMPACT TEST PROCEDURES - ROAD VEHICLES
SAE-J1752-1-1997 ELECTROMAGNETIC COMPATIBILITY MEASUREMENT PROCEDURES FOR INTEGRATED CIRCUITS - INTEGRATED CIRCUIT EMC
MEASUREMENT PROCEDURES - GENERAL AND DEFINITIONS
SAE-J1752-2-2003 (R) MEASUREMENT OF RADIATED EMISSIONS FROM INTEGRATED CIRCUITSSURFACE SCAN METHOD (LOOP PROBE METHOD) 10 MHZ
TO 3 GHZ
SAE-J1752-3-2003 (R) MEASUREMENT OF RADIATED EMISSIONS FROM INTEGRATED CIRCUITSTEM/WIDEBAND TEM (GTEM) CELL METHOD; TEM CELL
(150 KHZ TO 1 GHZ), WIDEBAND TEM CELL (150 KHZ TO 8 GHZ)
SAE-J1754-1-2001 (R) HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 1: PROCUREMENT DOCUMENT
SAE-J1754-2-2006 HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 2: ORDERING INFORMATION
SAE-J1755-1995 GUIDELINES FOR USAGE OF STAINLESS STEEL AND BIMETAL FOR EXTERIOR AUTOMOTIVE BRIGHT TRIM, RECOMMENDED PRACTICE
- JANUARY 1995
SAE-J1756-1994 TEST PROCEDURE TO DETERMINE THE FOGGING CHARACTERISTICS OF INTERIOR AUTOMOTIVE MATERIALS, RECOMMENDED PRACTICE
- DECEMBER 1994; REPLACES FLTM BO 116-03
SAE-J1757-1-2002 STANDARD METROLOGY FOR VEHICULAR DISPLAYS
SAE-J1759-2000 SAE HOSE MEASUREMENT STUDY
SAE-J1760-2001 DATA SECURITY SERVICES
SAE-J176-1994 (R) FAST FILL FUELING INSTALLATION FOR OFF-ROAD SELF-PROPELLED WORK MACHINES - DECEMBER 1994
SAE-J1765-1995 SAE MINIATURE BULB VIBRATION TEST, RECOMMENDED PRACTICE - MAY 1995
SAE-J1766-2005 (R) RECOMMENDED PRACTICE FOR ELECTRIC AND HYBRID ELECTRIC VEHICLE BATTERY SYSTEMS CRASH INTEGRITY TESTING
SAE-J1767-1995 INSTRUMENTAL COLOR DIFFERENCE MEASUREMENTS FOR COLORFASTNESS OF AUTOMOTIVE INTERIOR TRIM MATERIALS,
RECOMMENDED PRACTICE - JANUARY 1995
SAE-J1770-1995 AUTOMOTIVE REFRIGERANT RECOVERY/RECYCLING EQUIPMENT INTENDED FOR USE WITH BOTH R12 AND R134A, STANDARD -
OCTOBER 1995
SAE-J1771-1998 CRITERIA FOR REFRIGERANT IDENTIFICATION EQUIPMENT FOR USE WITH MOBILE AIR-CONDITIONING SYSTEMS
SAE-J1772-2001 (R) SAE ELECTRIC VEHICLE CONDUCTIVE CHARGE COUPLER
SAE-J1773-1999 (R) SAE ELECTRIC VEHICLE INDUCTIVE COUPLED CHARGING
SAE-J1774-2004 DESIGN GUIDELINES FOR FIBERBOARD MATERIALS
SAE-J1775/-HIR-1559A-1984 BLEED-AIR PNEUMATIC SYSTEMS FOR GAS TURBINE EQUIPPED MARINE AND AMPHIBIOUS CRAFT
SAE-J1776-2005 (R) MARINE VEHICLESHYDRAULIC PUMPSDESIGN AND SPECIFICATION GUIDE - SUPERSEDING J1776/HIR1514A
SAE-J1777/-HIR-1063B-1990 (R) GENERAL ENVIRONMENTAL CONSIDERATIONS FOR MARINE VEHICLES, INFORMATION REPORT
SAE-J1778-1998 (R) SHIP SYSTEMS AND EQUIPMENT - RECOMMENDED PRACTICE FOR HYDRAULIC FLUID SELECTION
SAE-J1779-2003 (R) SHIP SYSTEMS AND EQUIPMENT G窃 HYDRAULIC SYSTEM DESIGN CRITERIA FOR MARINE VEHICLES
SAE-J1780/-HRP-4382-1991 HYDRAULIC SYSTEM DIAGRAMS AND ASSOCIATED TABLES FOR MARINE VEHICLES
SAE-J1781/-HIR-1694-1982 MATERIALS FOR FLUID SYSTEMS OF MARINE VEHICLES
SAE-J1782-2000 (R) SHIP SYSTEMS AND EQUIPMENT - HYDRAULIC SYSTEMS - NOISE CONTROL - SUPERSEDES J 1782/HIR 1622A-1986 (R1992)
SAE-J1783-2002 (R) SHIP SYSTEMS AND EQUIPMENTSELECTION OF HYDRAULIC DIRECTIONAL CONTROL VALVES
SAE-J1787-2005 MEASUREMENT OF THE TOTAL ASH CONTENT OF AVIATION PISTON ENGINE OILS BY A CALCULATION METHOD
SAE-J1789-2002 SELF-PROPELLED SWEEPERS AND SCRUBBERS BRAKING PERFORMANCE
SAE-J1790-1998 SELF-PROPELLED SWEEPERS AND SCRUBBERS STEERING REQUIREMENTS SINGLE-CIRCUIT HYDRAULIC SERVO-ASSISTED SYSTEMS
SAE-J1791-2002 SELF-PROPELLED SWEEPERS AND SCRUBBERS DUAL POSITION DRIVING CONTROLS AND DISPLAYS
SAE-J179-2001 LABELING - DISC WHEELS AND DEMOUNTABLE RIMS - TRUCKS
SAE-J1792-1-2002 SELF-PROPELLED SWEEPERS - AIR FLOW PERFORMANCE PART 1: SUCTION AIR VOLUME PERFORMANCE
SAE-J1792-2-2002 SELF-PROPELLED SWEEPERS - AIR FLOW PERFORMANCE PART 2: SUCTION/BLOWER FAN PERFORMANCE
SAE-J1793-1999 SELF-PROPELLED SWEEPERS AND SCRUBBERS TANK AND HOPPER CAPACITY RATING
SAE-J1794-1996 SAE RESTRAINT SYSTEMS EFFLUENT TEST PROCEDURE
SAE-J1796-2005 SPECTRAL TRANSMISSION TEST
SAE-J1797-1997 RECOMMENDED PRACTICE FOR PACKAGING OF ELECTRIC VEHICLE BATTERY MODULES
SAE-J1798-1997 RECOMMENDED PRACTICE FOR PERFORMANCE RATING OF ELECTRICAL VEHICLE BATTERY MODULES
SAE-J1800-1987 METHOD FOR EVALUATING THE PAINTABLE CHARACTERISTICS OF AUTOMOTIVE SEALERS, RECOMMENDED PRACTICE - APRIL 1987
SAE-J1801-1993 BRAKE EFFECTIVENESS MARKING FOR BRAKE BLOCKS
SAE-J180-2002 (R) ELECTRICAL CHARGING SYSTEMS FOR OFF HIGHWAY WORK MACHINES
SAE-J1802-1-2003 TEST COMPONENT SPECIFICATIONS
SAE-J1802-2001 BRAKE BLOCK EFFECTIVENESS RATING
SAE-J1803-1997 SEAT BELT RESTRAINT SYSTEM HARDWARE - GLOSSARY OF TERMS
SAE-J1804-1989 CORROSION PREVENTIVE COMPOUND, TOPSIDE VEHICLE CORROSION PROTECTION, STANDARD - JUNE 1989
SAE-J1805-2003 SOUND POWER LEVEL MEASUREMENTS OF WORK MACHINES STATIC AND IN-PLACE DYNAMIC METHODS
SAE-J1806-1999 (R) CLUTCH DIMENSIONS FOR TRUCK AND BUS APPLICATIONS
SAE-J1807-2000 HYDRAULIC POWER ASSIST BRAKE BOOSTER TEST PROCEDURE
SAE-J1808-1989 VACUUM POWER ASSIST BRAKE BOOSTER TEST PROCEDURE, STANDARD - OCTOBER 1989
SAE-J1810-2002 (R) ELECTRICAL INDICATING SYSTEM SPECIFICATION
SAE-J1811-2002 POWER CABLE TERMINALS
SAE-J1812-2003 FUNCTION PERFORMANCE STATUS CLASSIFICATION FOR EMC IMMUNITY TESTING
SAE-J1814-1993 OPERATOR CONTROLSOFF-ROAD MACHINES
SAE-J1817-2001 LONG-STROKE AIR-BRAKE ACTUATOR MARKING
SAE-J1819-1994 SECURING CHILD RESTRAINT SYSTEMS IN MOTOR VEHICLES
SAE-J18-2002 SPONGE AND EXPANDED CELLULAR RUBBER PRODUCTS
SAE-J182-1997 MOTOR VEHICLE FIDUCIAL MARKS AND THREE-DIMENSIONAL REFERENCE SYSTEM
SAE-J1824-1991 SPECIFICATION DEFINITIONS - CLAM BUNK SKIDDER
SAE-J1825-2005 SHELF STORAGE OF HYDRAULIC BRAKE COMPONENTS
SAE-J1826-1989 TURBOCHARGER GAS STAND TEST CODE, RECOMMENDED PRACTICE;
SAE-J1828-1996 (R) UNIFORM REFERENCE AND DIMENSIONAL GUIDELINES FOR COLLISION REPAIR
SAE-J1829-1992 STOICHIOMETRIC AIR-FUEL RATIOS OF AUTOMOTIVE FUELS
SAE-J1830-1987 SIZE CLASSIFICATION AND CHARACTERISTICS OF CERAMIC SHOT FOR PEENING, RECOMMENDED PRACTICE - MAY 1987
SAE-J183-2006 (R) ENGINE OIL PERFORMANCE AND ENGINE SERVICE CLASSIFICATION (OTHER THAN G牵ENERGY CONSERVINGG钎)
SAE-J1832-2001 LOW PRESSURE GASOLINE FUEL INJECTOR
SAE-J1834-1991 SEAT BELT COMFORT, FIT, AND CONVENIENCE
SAE-J1835-1999 FASTENER HARDWARE FOR WHEELS FOR DEMOUNTABLE RIMS
SAE-J1836-1988 OVERLAP SHEAR TEST FOR SEALANT ADHESIVE BONDING OF AUTOMOTIVE GLASS ENCAPSULATING MATERIAL TO BODY OPENING,
RECOMMENDED PRACTICE - OCTOBER 1988
SAE-J1837-1991 ELECTROPLATE REQUIREMENTS FOR DECORATIVE CHROMIUM DEPOSITS ON ZINC BASE MATERIALS USED FOR EXTERIOR
ORNAMENTATION, STANDARD - JUNE 1991
SAE-J1839-1997 COARSE DROPLET WATER/FUEL SEPARATION TEST PROCEDURE
SAE-J184-1998 (R) QUALIFYING A SOUND DATA ACQUISITION SYSTEM
SAE-J1842-2004 (R) DISC WHEEL HUB/SPOKE WHEEL AND AXLE INTERFACE DIMENSIONSCOMMERCIAL VEHICLES
SAE-J1843-1993 ACCELERATOR PEDAL POSITION SENSOR FOR USE WITH ELECTRONIC CONTROLS IN MEDIUM- AND HEAVY-DUTY VEHICLE
APPLICATIONS, RECOMMENDED PRACTICE - APRIL 1993
SAE-J1846-2003 CHARACTERIZING A TEST SURFACE FOR MOTORCYCLE SIDE STAND RETRACTION PERFORMANCE TESTING
SAE-J1847-1989 ABRASION RESISTANCE TESTING - VEHICLE EXTERIOR GRAPHICS AND PIN STRIPING, RECOMMENDED PRACTICE - JUNE 1989
SAE-J1849-2002 (R) EMERGENCY VEHICLE SIRENS
SAE-J1850-2001 CLASS B DATA COMMUNICATIONS NETWORK INTERFACE
SAE-J1851-1987 INDUCTION CURE TEST FOR METAL BONDING ADHESIVES, RECOMMENDED PRACTICE - MAY 1987
SAE-J185-1988 ACCESS SYSTEMS FOR OFF-ROAD MACHINES
SAE-J1853-1987 HAND WINCHES - BOAT TRAILER TYPE
SAE-J1854-2003 (R) BRAKE FORCE DISTRIBUTION PERFORMANCE GUIDETRUCK AND BUS
SAE-J1855-2001 (R) DEPLOYMENT OF ELECTRICALLY ACTIVATED AUTOMOTIVE AIR BAGS FOR AUTOMOBILE RECLAMATION
SAE-J1857-2003 FLYWHEEL DIMENSIONS FOR TRUCK AND BUS APPLICATIONS
SAE-J1859-2003 TEST PROCEDURES FOR DETERMINING AIR BRAKE VALVE INPUT-OUTPUT CHARACTERISTICS
SAE-J1860-2003 LABELING AIR BRAKE VALVES WITH THEIR PERFORMANCE (INPUT-OUTPUT) CHARACTERISTICS
SAE-J1861-1994 AIR BRAKE VALVE INPUT-OUTPUT CHARACTERISTIC REQUIREMENTS
SAE-J1862-2000 (R) FUEL INJECTION SYSTEM FUEL PRESSURE REGULATOR AND PRESSURE DAMPER
SAE-J1863-1987 COACH JOINT FRACTURE TEST, RECOMMENDED PRACTICE - APRIL 1987
SAE-J1864-1987 METHOD FOR EVALUATING MATERIAL SEPARATION IN AUTOMOTIVE SEALERS UNDER PRESSURE IN STATIC CONDITIONS,
RECOMMENDED PRACTICE
SAE-J1865-1999 DIMENSIONAL COMPATIBILITY FOR COMMERCIAL VEHICLES FITMENT OF COMPLETE WHEELS
SAE-J1868-1993 (R) RESTRICTED HARDENABILITY BANDS FOR SELECTED ALLOY STEELS, STANDARD - SEPTEMBER 1993
SAE-J187-1970 TRUCK VEHICLE IDENTIFICATION NUMBERS - OCTOBER 1970
SAE-J1873-2003 MOISTURE TRANSMISSION TEST PROCEDUREHYDRAULIC BRAKE HOSE ASSEMBLIES
SAE-J1875-1993 MATERIALS FOR PLASTIC CHECK VALVES FOR VACUUM BOOSTER SYSTEMS
SAE-J1876-1990 PLASTIC DUST SHIELD FOR HYDRAULIC DISC BRAKES
SAE-J1877-1988 RECOMMENDED PRACTICE FOR BAR-CODED VEHICLE IDENTIFICATION NUMBER LABEL, RECOMMENDED PRACTICE
SAE-J1879-1988 GENERAL QUALIFICATION AND PRODUCTION ACCEPTANCE CRITERIA FOR INTEGRATED CIRCUITS IN AUTOMOTIVE APPLICATIONS,
RECOMMENDED PRACTICE - OCTOBER 1988
SAE-J188-2003 POWER STEERING PRESSURE HOSE - HIGH VOLUMETRIC EXPANSION TYPE
SAE-J1883-1988 ELASTOMERIC BUSHING "TRAC" APPLICATION CODE, RECOMMENDED PRACTICE
SAE-J1885-2005 ACCELERATED EXPOSURE OF AUTOMOTIVE INTERIOR TRIM COMPONENTS USING A CONTROLLED IRRADIANCE WATER COOLED XENON-
ARC APPARATUS
SAE-J1887-2002 AUTOMOTIVE COMPACTED GRAPHITE IRON CASTINGS
SAE-J1888-1990 HIGH CURRENT TIME LAG ELECTRIC FUSES, STANDARD - NOVEMBER 1990
SAE-J1889-2005 L.E.D. SIGNAL AND MARKING LIGHTING DEVICES
SAE-J1890-1988 PERFORMANCE ASSURANCE OF REMANUFACTURED, HYDRAULICALLY- OPERATED RACK AND PINION STEERING GEARS
SAE-J189-2003 POWER STEERING RETURN HOSE - LOW PRESSURE
SAE-J1892-1998 (R) RECOMMENDED PRACTICE FOR BAR-CODED VEHICLE EMISSION CONFIGURATION LABEL
SAE-J1899-2005 LUBRICATING OIL, AIRCRAFT PISTON ENGINE (ASHLESS DISPERSANT)
SAE-J190-1998 POWER STEERING PRESSURE HOSE - WIRE BRAID - AUGUST 1970
SAE-J1903-1997 (R) AUTOMOTIVE ADAPTIVE DRIVER CONTROLS, MANUAL
SAE-J1907-1988 PEEL ADHESION TEST FOR GLASS TO ELASTOMERIC MATERIAL FOR AUTOMOTIVE GLASS ENCAPSULATION, RECOMMENDED PRACTICE
SAE-J1908-2002 (R) ELECTRICAL GROUNDING PRACTICE
SAE-J1911-2003 TEST PROCEDURE FOR AIR RESERVOIR CAPACITY - HIGHWAY TYPE VEHICLES
SAE-J191-2003 POWER STEERING PRESSURE HOSE - LOW VOLUMETRIC EXPANSION TYPE
SAE-J1915-1990 RECOMMENDED REMANUFACTURING PROCEDURES FOR MANUAL TRANSMISSION CLUTCH ASSEMBLIES
SAE-J1916-1989 ENGINE WATER PUMP REMANUFACTURE PROCEDURES AND ACCEPTANCE CRITERIA, RECOMMENDED PRACTICE - MAY 1989
SAE-J1918-2002 (R) METHOD FOR THE DETERMINATION OF EXPANSION AND WATER ABSORPTION OF AUTOMOTIVE SEALERS
SAE-J192-2003 (R) MAXIMUM EXTERIOR SOUND LEVEL FOR SNOWMOBILES
SAE-J1922-1995 POWERTRAIN CONTROL INTERFACE FOR ELECTRONIC CONTROLS USED IN MEDIUM AND HEAVY-DUTY DIESEL ON-HIGHWAY VEHICLE
APPLICATIONS
SAE-J1927-2001 CUMULATIVE DAMAGE ANALYSIS FOR HYDRAULIC HOSE ASSEMBLIES
SAE-J1928-2005 DEVICES PROVIDING BACKFIRE FLAME CONTROL FOR GASOLINE ENGINES IN MARINE APPLICATIONS
SAE-J1930-2002 ELECTRICAL/ELECTRONIC SYSTEMS DIAGNOSTIC TERMS, DEFINITIONS, ABBREVIATIONS, AND ACRONYMSEQUIVALENT TO ISO/TR
15031-2:APRIL 30, 2002
SAE-J193-1987 BALL STUD AND SOCKET ASSEMBLY - TEST PROCEDURES
SAE-J1938-1998 (R) DESIGN/PROCESS CHECKLIST FOR VEHICLE ELECTRONIC SYSTEMS
SAE-J1939-01-2000 RECOMMENDED PRACTICE FOR CONTROL AND COMMUNICATION NEWTWORK FOR ON-HIGHWAY EQUIPMENT
SAE-J1939-11-1999 PHYSICAL LAYER, 250K BITS/S, TWISTED SHIELDED PAIR
SAE-J1939-13-2004 OFF-BOARD DIAGNOSTIC CONNECTOR
SAE-J1939-15-2003 REDUCED PHYSICAL LAYER, 250K BITS/SEC, UN-SHIELDED TWISTED PAIR (UTP)
SAE-J1939-2005 (R) RECOMMENDED PRACTICE FOR A SERIAL CONTROL AND COMMUNICATIONS VEHICLE NETWORK
SAE-J1939-21-2001 DATA LINK LAYER
SAE-J1939-31-2004 NETWORK LAYER
SAE-J1939-71-2006 VEHICLE APPLICATION LAYER (THROUGH DECEMBER 2004)
SAE-J1939-73-2004 APPLICATION LAYER - DIAGNOSTICS
SAE-J1939-74-2004 APPLICATIONCONFIGURABLE MESSAGING
SAE-J1939-75-2002 APPLICATION LAYERGENERATOR SETS AND INDUSTRIAL
SAE-J1939-81-2003 NETWORK MANAGEMENT
SAE-J1940-2002 (R) SMALL ENGINE POWER AND TORQUE RATING PROCEDURE
SAE-J1941-1990 COOLANT CONCENTRATE (LOW SILICATE, ETHYLENE GLYCOL TYPE REQUIRING AN INITIAL CHARGE OF SUPPLEMENTAL COOLANT
ADDITIVE) FOR HEAVY-DUTY ENGINES
SAE-J1942-1-2005 QUALIFIED HOSES FOR MARINE APPLICATIONS
SAE-J1942-2002 HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS
SAE-J1944-1991 TRUCK AND BUS MULTIPURPOSE VEHICLE WINDSHIELD WASHER SYSTEM
SAE-J1945-2000 CROSS-TOOTH COMPANION FLANGES, TYPE T
SAE-J1946-2001 COMPANION FLANGES, TYPE A (EXTERNAL PILOT) AND TYPE S (INTERNAL PILOT)
SAE-J1948-1989 CAB SLEEPER OCCUPANT RESTRAINT SYSTEM TEST
SAE-J1949-1988 ROAD VEHICLES - HIGH PRESSURE FUEL INJECTION PIPE END-CONNECTIONS WITH 60 DEGREE FEMALE CONE, STANDARD; -
OCTOBER 1988 (ISO/DIS 2974)
SAE-J1950-1989 PROVING GROUND VEHICLE CORROSION TESTING, INFORMATION REPORT - MAY 1989
SAE-J195-1970 AUTOMATIC VEHICLE SPEED CONTROL - MOTOR VEHICLES
SAE-J1952-2003 (R) ALL-WHEEL DRIVE SYSTEMS CLASSIFICATION
SAE-J1953-2001 BRAKE-STROKE INDICATOR DESIGN GUIDELINE FOR CAM OR DISC AIR-BRAKE ACTUATORS
SAE-J1957-2000 (R) CENTER HIGH MOUNTED STOP LAMP STANDARD FOR VEHICLES LESS THAN 2032 MM OVERALL WIDTH
SAE-J1958-1989 DIESEL ENGINES - STEEL TUBES FOR HIGH-PRESSURE FUEL INJECTION PIPES (TUBING)
SAE-J1959-1989 CORROSION PREVENTIVE COMPOUND, UNDERBODY VEHICLE CORROSION PROTECTION - SUPERSEDING J1969 JUN1998
SAE-J1960-2004 ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A CONTROLLED IRRADIANCE WATER-COOLED XENON ARC
APPARATUS
SAE-J1961-2002 (R) ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A SOLAR FRESNEL REFLECTOR APPARATUS
SAE-J1962-2002 (R) DIAGNOSTIC CONNECTOR EQUIVALENT TO ISO/DIS 15031-3:DECEMBER 14, 2001
SAE-J1965-2003 ROAD VEHICLES - WHEELS FOR COMMERCIAL VEHICLES AND MULTIPURPOSE PASSENGER VEHICLES - FIXING NUTS - TEST
METHODS
SAE-J1966-2005 LUBRICATING OILS, AIRCRAFT PISTON ENGINE (NON-DISPERSANT MINERAL OIL)
SAE-J1967-2006 RETROREFLECTIVE MATERIALS FOR VEHICLE CONSPICUITY
SAE-J1969-1988 ELECTROCOAT COMPATIBILITIES OF AUTOMOTIVE SEALERS, RECOMMENDED PRACTICE - OCTOBER 1988
SAE-J1970-2003 SHORELINE SOUND LEVEL MEASUREMENT PROCEDURE FOR RECREATIONAL MOTORBOATS
SAE-J1973-1991 PERSONAL WATERCRAFT - FLOTATION, RECOMMENDED PRACTICE - APRIL 1991
SAE-J1974-1993 DECORATIVE ANODIZING SPECIFICATION FOR AUTOMOTIVE APPLICATIONS, RECOMMENDED PRACTICE - JUNE 1993
SAE-J1975-1997 CASE HARDENABILITY OF CARBURIZED STEELS
SAE-J1976-2002 (R) OUTDOOR WEATHERING OF EXTERIOR MATERIALS
SAE-J1977-1997 BRAKING PERFORMANCE - RUBBER-TIRED, SELF-PROPELLED CRANES
SAE-J1978-2002 OBD II SCAN TOOL EQUIVALENT TO ISO/DIS 15031-4:DECEMBER 14, 2001
SAE-J1979-2002 (R) E/E DIAGNOSTIC TEST MODES EQUIVALENT TO ISO/DIS 15031-5:APRIL 30, 2002
SAE-J1980-2001 (R) GUIDELINES FOR EVALUATING OUT-OF-POSITION VEHICLE OCCUPANT INTERACTIONS WITH DEPLOYING AIRBAGS
SAE-J1981-2005 ROAD HAZARD IMPACT TEST FOR WHEEL AND TIRE ASSEMBLIES (PASSENGER CAR, LIGHT TRUCK, AND MULTIPURPOSE VEHICLES)
SAE-J198-2003 WINDSHIELD WIPER SYSTEMSTRUCKS, BUSES, AND MULTIPURPOSE VEHICLES
SAE-J1982-1998 (R) NOMENCLATURE - WHEELS FOR PASSENGER CARS, LIGHT TRUCKS, AND MULTIPURPOSE VEHICLES
SAE-J1984-1995 DIESEL FUEL INJECTOR ASSEMBLY TYPE 28 (9.5 MM) - (THIS DOCUMENT REFERENCES ISO 2698)
SAE-J1985-1993 FUEL FILTERS - INITIAL SINGLE-PASS EFFICIENCY TEST METHOD, STANDARD - OCTOBER 1993
SAE-J1986-2006 BALANCE WEIGHT AND RIM FLANGE DESIGN SPECIFICATIONS, TEST PROCEDURES, AND PERFORMANCE RECOMMENDATIONS
SAE-J1987-1998 FORCE AND MOVEMENT TEST METHOD
SAE-J1988-1994 RESIDUAL ALIGNING MOMENT TEST, RECOMMENDED PRACTICE - AUGUST 1994
SAE-J1989-1998 RECOMMENDED SERVICE PROCEDURE FOR THE CONTAINMENT OF CFC-12 (R-12)
SAE-J1990-1999 RECOVERY AND RECYCLE EQUIPMENT FOR MOBILE AUTOMOTIVE AIR-CONDITIONING SYSTEMS
SAE-J1991-1999 STANDARD OF PURITY FOR USE IN MOBILE AIR-CONDITIONING SYSTEMS - OCTOBER 1989
SAE-J1992-2001 (R) WHEELS/RIMS - MILITARY VEHICLES - TEST PROCEDURES AND PERFORMANCE REQUIREMENTS
SAE-J1993-1996 HIGH-CARBON CAST-STEEL GRIT
SAE-J1994-2004 LABORATORY TESTING OF VEHICLE AND INDUSTRIAL HEAT EXCHANGERS FOR HEAT TRANSFER PERFORMANCE
SAE-J1995-1990 ENGINE POWER TEST CODE - SPARK IGNITION AND COMPRESSION IGNITION - GROSS POWER RATING, STANDARD;
SAE-J1996-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - QUALITY REQUIREMENTS
SAE-J1997-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - RECTANGULAR RINGS
SAE-J1998-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - RECTANGULAR RINGS WITH NARROW RING WIDTH
SAE-J1999-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - SCRAPER RINGS
SAE-J2000-1998 INTERNAL COMBUSTION ENGINES - PISTON RINGS - KEYSTONE RINGS
SAE-J2001-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - HALF KEYSTONE RINGS
SAE-J200-2005 CLASSIFICATION SYSTEM FOR RUBBER MATERIALS - REPLACES SAE J14/ASTM D 735
SAE-J2002-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - OIL CONTROL RINGS
SAE-J2003-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS COIL SPRING LOADED OIL CONTROL RINGS
SAE-J2004-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - EXPANDER/SEGMENT OIL CONTROL RINGS
SAE-J2005-2004 STATIONARY SOUND LEVEL MEASUREMENT PROCEDURE FOR RECREATIONAL MOTORBOATS
SAE-J2006-2003 MARINE EXHAUST HOSE
SAE-J2008-1998 ELECTRONIC PRODUCT - PLEASE REFER TO GLOBAL
SAE-J2009-2005 (R) DISCHARGE FORWARD LIGHTING SYSTEM AND SUBSYSTEMS
SAE-J201-1976 IN-SERVICE BRAKE PERFORMANCE TEST PROCEDURE PASSENGER-CAR AND LIGHT-DUTY TRUCK
SAE-J20-1-2002 COOLANT HOSE - SUPPLEMENT TO SAE J20 FOR GOVERMENT USE REPLACING PART OF MS521130
SAE-J2012-2002 (R) DIAGNOSTIC TROUBLE CODE DEFINITIONS EQUIVALENT TO ISO/DIS 15031-6:APRIL 30, 2002
SAE-J2013-1991 MILITARY TIRE GLOSSARY, RECOMMENDED PRACTICE - MAY 1991
SAE-J2014-2001 (R) PNEUMATIC TIRES FOR MILITARY TACTICAL WHEELED VEHICLES - FSC 2610
SAE-J2016-1999 (R) CHEMICAL STRESS RESISTANCE OF POLYMERS
SAE-J2017-1995 (R) GUIDELINES FOR THE DEVELOPMENT OF PERFORMANCE-BASED TECHNICIAN TRAINING PROGRAMS, RECOMMENDED PRACTICE -
JULY 1995
SAE-J2018-1989 ASSESSING TECHNICIAN TRAINING, RECOMMENDED PRACTICE - JULY 1989
SAE-J2019-1994 ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A CONTROLLED IRRADIANCE AIR-COOLED XENON-ARC
APPARATUS, STANDARD - JANUARY 1994
SAE-J20-2004 COOLANT SYSTEM HOSES
SAE-J2020-2003 ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A FLUORESCENT UV AND CONDENSATION APPARATUS
SAE-J20-2-2001 COOLANT HOSE - NORMAL SERVICE TYPE CONVOLUTED, WIRE SUPPORT HOSE (SUPPLEMENT TO SAE J20 FOR GOVERNMENT USE
REPLACING PART OF MS51008)
SAE-J2022-2000 CLASSIFICATION, NOMENCLATURE, AND SPECIFICATION DEFINITIONS FOR HORIZONTAL EARTHBORING MACHINES
SAE-J2024-1993 CONTAMINANTS FOR TESTING AIR BRAKE COMPONENTS AND AUXILIARY PNEUMATIC DEVICES
SAE-J2025-1989 METHOD FOR EVALUATING THE FLOW PROPERTIES OF PUMPABLE SEALERS, RECOMMENDED PRACTICE - JUNE 1989
SAE-J2027-1998 (R) STANDARD FOR PROTECTIVE COVERS FOR GASOLINE FUEL LINE TUBING
SAE-J2028-2000 FRONT-WHEEL-DRIVE CONSTANT VELOCITY JOINT BOOT SEALS
SAE-J2030-2002 (R) HEAVY-DUTY ELECTRICAL CONNECTOR PERFORMANCE STANDARD
SAE-J2031-2001 HIGH TENSION IGNITION CABLE
SAE-J2032-2000 (R) IGNITION CABLE ASSEMBLIES
SAE-J2034-1993 PERSONAL WATERCRAFT VENTILATION SYSTEMS, RECOMMENDED PRACTICE - JANUARY 1993
SAE-J2039-2001 SIDE TURN SIGNAL LAMPS FOR LONG VEHICLES
SAE-J2040-2002 TAIL LAMPS (REAR POSITION LAMPS) FOR USE ON VEHICLES 2032 MM OR MORE IN OVERALL WIDTH
SAE-J2041-1999 REFLEX REFLECTORS FOR USE ON VEHICLES 2032 MM OR MORE IN OVERALL WIDTH
SAE-J2042-2003 CLEARANCE, SIDEMARKER, AND IDENTIFICATION LAMPS FOR USE ON MOTOR VEHICLES 2032 MM OR MORE IN OVERALL WIDTH
SAE-J2044-2002 QUICK CONNECT COUPLING SPECIFICATION FOR LIQUID FUEL AND VAPOR/EMISSIONS SYSTEMS
SAE-J2045-1998 (R) PERFORMANCE REQUIREMENTS FOR FUEL SYSTEM TUBING ASSEMBLIES
SAE-J2046-1993 PERSONAL WATERCRAFT FUEL SYSTEMS, RECOMMENDED PRACTICE - JANUARY 1993
SAE-J2047-1998 TIRE PERFORMANCE TECHNOLOGY
SAE-J2050-2001 HIGH-TEMPERATURE POWER STEERING PRESSURE HOSE
SAE-J2051-2005 QUALIFICATIONS FOR FOUR-WAY SUBBASE MOUNTED AIR VALVES FOR AUTOMOTIVE MANUFACTURING APPLICATIONS
SAE-J2052-1997 TEST DEVICE HEAD CONTACT DURATION ANALYSIS
SAE-J2053-1994 BRAKE MASTER CYLINDER PLASTIC RESERVOIR ASSEMBLY FOR ROAD VEHICLES, RECOMMENDED PRACTICE - JUNE 1994
SAE-J2056-3-1991 SELECTION OF TRANSMISSION MEDIA
SAE-J2057-1-1997 (R) CLASS A APPLICATION/DEFINITION
SAE-J2057-2-2001 CLASS A MULTIPLEXING ACTUATORS
SAE-J2057-3-1993 CLASS A MULTIPLEXING SENSORS
SAE-J2057-4-1993 CLASS A MULTIPLEXING ARCHITECTURE STRATEGIES
SAE-J2059-1992 ALL-WHEEL-DRIVE DRIVETRAIN SCHEMATIC SYMBOL STANDARDS
SAE-J2064-2005 R134A REFRIGERANT AUTOMOTIVE AIR-CONDITIONED HOSE
SAE-J2066-1994 FILTER AND FILTER ELEMENT FOR HYDRAULIC SYSTEM(S) USED ON MANUFACTURING AND ASSEMBLY EQUIPMENT, STANDARD -
FEBRUARY 1994
SAE-J2069-2001 RECOVERY ATTACHMENT POINTS FOR PASSENGER CARS, VANS, AND LIGHT TRUCKS - FEBRUARY 2001
SAE-J2071-1994 AERODYNAMIC TESTING OF ROAD VEHICLES - OPEN THROAT WIND TUNNEL ADJUSTMENT, INFORMATION REPORT - JUNE 1994
SAE-J207-1970 ELECTROPLATING OF NICKEL AND CHROMIUM ON METAL PARTS - AUTOMOTIVE ORNAMENTATION AND HARDWARE, STANDARD;
SAE-J2073-1993 AUTMOTIVE STARTER REMANUFACTURING PROCEDURES
SAE-J2074-2000 THE AIR BAG SYSTEMS IN YOUR CAR "WHAT THE PUBLIC NEEDS TO KNOW"
SAE-J2075-2001 ALTERNATOR REMANUFACTURING/REBUILDING PROCEDURES INCLUDES PASSENGER CAR, HEAVY DUTY, INDUSTRIAL, AGRICULTURAL,
AND MARINE
SAE-J2076-2001 HIGH-TEMPERATURE POWER STEERING RETURN HOSE - LOW PRESSURE
SAE-J2077-1990 MINIATURE BLADE TYPE ELECTRICAL FUSES, STANDARD - NOVEMBER 1990
SAE-J2079-1992 LOCATION OF ATOMIZER OF ETHER SYSTEMS FOR DIESEL ENGINES, INFORMATION REPORT - MAY 1992
SAE-J2081-1997 (R) TEST PROCEDURE FOR DETERMINING THE RESISTANCE OF SAFETY-GLAZING MATERIALS, OF WHICH ONE SURFACE IS
PLASTIC, TO SIMULATED WEATHERING
SAE-J2082-1992 COOLING FLOW MEASUREMENT TECHNIQUES, INFORMATION REPORT - JUNE 1992
SAE-J2084-1993 AERODYNAMIC TESTING OF ROAD VEHICLES-TESTING METHODS AND PROCEDURES, INFORMATION REPORT - JANUARY 1993
SAE-J2087-2006 (R) DAYTIME RUNNING LIGHT
SAE-J2092-1995 TESTING OF WHEELCHAIR LIFTS FOR ENTRY TO OR EXIT FROM A PERSONALLY LICENSED VEHICLE
SAE-J2093-1995 DESIGN CONSIDERATIONS FOR WHEELCHAIR LIFTS FOR ENTRY TO OR EXIT FROM A PERSONALLY LICENSED VEHICLE
SAE-J2094-2001 (R) VEHICLE AND CONTROL MODIFICATIONS FOR DRIVERS WITH PHYSICAL DISABILITIES TERMINOLOGY
SAE-J2099-1999 STANDARD OF PURITY FOR RECYCLED HFC-134A (R-134A) FOR USE IN MOBILE AIR-CONDITIONING SYSTEMS
SAE-J2100-1992 ACCELERATED ENVIRONMENTAL TESTING FOR BONDED AUTOMOTIVE ASSEMBLIES, RECOMMENDED PRACTICE - AUGUST 1992
SAE-J2108-1991 DOOR COURTESY SWITCH
SAE-J211-1-2003 (R) INSTRUMENTATION FOR IMPACT TEST - PART 1 - ELECTRONIC INSTRUMENTATION
SAE-J2111-2005 HEADLAMP CLEANERS
SAE-J211-2-2001 (R) INSTRUMENTATION FOR IMPACT TEST - PART 2: PHOTOGRAPHIC INSTRUMENTATION
SAE-J2114-1999 DOLLY ROLLOVER RECOMMENDED TEST PROCEDURE
SAE-J2115-1993 BRAKE PERFORMANCE AND WEAR TEST CODE COMMERCIAL VEHICLE INERTIA DYNAMOMETER
SAE-J2116-2003 TWO-STROKE-CYCLE GASOLINE ENGINE LUBRICANTS PERFORMANCE AND SERVICE CLASSIFICATION
SAE-J2118-2006 BRAKING PERFORMANCE - ASPHALT PAVERS
SAE-J2119-1993 MANUAL CONTROLS FOR MATURE DRIVERS
SAE-J2120-1992 PERSONAL WATERCRAFT - ELECTRICAL SYSTEMS
SAE-J2121-1995 REQUIREMENTS FOR COMPOSITE LIGHTING ASSEMBLIES USED ON CONSTRUCTION AND INDUSTRIAL MACHINERY
SAE-J212-1998 (R) BRAKE SYSTEM DYNAMOMETER TEST PROCEDURE - PASSENGER CAR
SAE-J2122-1998 NUMBERING SYSTEM FOR SINGLE DIAMETER DRILLS
SAE-J2123-1998 NUMBERING SYSTEM FOR TAPS
SAE-J2124-1998 NUMBERING SYSTEM FOR SINGLE DIAMETER AND TAPER REAMERS
SAE-J2129-1990 GUIDELINES FOR REQUESTS RECEIVED FROM OUTSIDE SOURCES FOR THE CONAG COUNCIL TO ORIGINATE OR REVIEW TECHNICAL
REPORTS, INFORMATION REPORT - NOVEMBER 1990
SAE-J2130-1997 (R) SELF-PROPELLED SWEEPERS AND CLEANING EQUIPMENT
SAE-J213-2004 MOTORCYCLE CLASSIFICATIONS
SAE-J2132-1995 MANUAL TRANSMISSIONS AND TRANSAXLE HIGH-SPEED LUBRICATION, UNBALANCE, AND SEIZURE EVALUATION
SAE-J2133-2001 (R) DISC WHEEL RADIAL RUNOUT LOW POINT MARKING
SAE-J2134-2005 (R) LUMINOUS REFLECTANCE IN SAFETY GLAZING MATERIALS FOR ROAD VEHICLES
SAE-J2139-2005 TESTS FOR SIGNAL AND MARKING DEVICES USED ON VEHICLES 2032 MM OR MORE IN OVERALL WIDTH
SAE-J2140-2000 GENERAL REQUIREMENT FOR PREFORMED HOSES FOR AIR INDUCTION ON HEAVY-DUTY ENGINES
SAE-J216-1999 (R) MOTOR VEHICLE GLAZING - ELECTRICAL CIRCUITS
SAE-J2162-1998 SPARK PLUG HEAT RATING CLASSIFICATIONS - FSC 5330
SAE-J217-1994 (R) STAINLESS STEEL 17-7 PH SPRING WIRE AND SPRINGS - JULY 1994
SAE-J2174-2002 (R) HEAVY-DUTY WIRING SYSTEMS FOR TRAILERS 2032 MM OR MORE IN WIDTH
SAE-J2175-1991 SPECIFICATIONS FOR LOW CARBON CAST STEEL SHOT, RECOMMENDED PRACTICE - JUNE 1991
SAE-J2177-1992 CHASSIS DYNAMOMETER TEST PROCEDURE - HEAVY-DUTY ROAD VEHICLES
SAE-J2178-1-1999 CLASS B DATA COMMUNICATION NETWORK MESSAGES DETAILED HEADER FORMATS AND PHYSICAL ADDRESS ASSIGNMENTS
SAE-J2178-2-1999 CLASS B DATA COMMUNICATION NETWORK MESSAGES PART 2: DATA PARAMETER DEFINITIONS
SAE-J2178-3-1999 CLASS B DATA COMMUNICATION NETWORK MESSAGESPART 3 FRAME IDS FOR SINGLE-BYTE FORMS OF HEADERS
SAE-J2178-4-1999 CLASS B DATA COMMUNICATION NETWORK MESSAGES MESSAGE DEFINITIONS FOR THREE BYTE HEADERS
SAE-J2180-1993 TILT TABLE PROCEDURE FOR MEASURING THE STATIC ROLLOVER THRESHOLD FOR HEAVY TRUCKS
SAE-J2181-1993 STEADY-STATE CIRCULAR TEST PROCEDURE FOR TRUCKS AND BUSES
SAE-J218-1981 PASSENGER CAR IDENTIFICATION TERMINOLOGY - DECEMBER 1981
SAE-J2183-2006 60 V AND 600 V SINGLE-CORE CABLES
SAE-J2184-2000 (R) VEHICLE LIFT POINTS FOR SERVICE GARAGE LIFTING
SAE-J2185-1997 LIFE TEST FOR HEAVY-DUTY STORAGE BATTERIES
SAE-J2186-1996 E/E DATA LINK SECURITY
SAE-J2188-2003 COMMERCIAL TRUCK AND BUS SAE RECOMMENDED PROCEDURE FOR VEHICLE PERFORMANCE PREDICTION AND CHARTING
SAE-J2189-2001 (R) GUIDELINES FOR EVALUATING CHILD RESTRAINT SYSTEM INTERACTIONS WITH DEPLOYING AIRBAGS
SAE-J2190-1993 ENHANCED E/E DIAGNOSTIC TEST MODES, RECOMMENDED PRACTICE - JUNE 1993
SAE-J2191-2004 RECOMMENDED PRACTICE FOR IDENTIFICATION OF STANDARDIZED TRUCK AND TRACTOR ELECTRICAL CIRCUITS
SAE-J2192-2005 RECOMMENDED TESTING METHODS FOR PHYSICAL PROTECTION OF WIRING HARNESSES
SAE-J2194-1987 ROLL-OVER PROTECTIVE STRUCTURES (ROPS) FOR WHEELED AGRICULTURAL TRACTORS
SAE-J2196-1992 SERVICE HOSE FOR AUTOMOTIVE AIR CONDITIONING
SAE-J2197-1992 HFC-134A (R-134A) SERVICE HOSE FITTINGS FOR AUTOMOTIVE AIR-CONDITIONING SERVICE EQUIPMENT
SAE-J2198-2000 (R) GLOSSARY - AUTOMATIC BELT TENSIONER
SAE-J2200-1991 PASSENGER CAR AND LIGHT TRUCK AXLES
SAE-J220-1991 CRANE BOOMSTOP
SAE-J2202-2004 (R) HEAVY-DUTY WIRING SYSTEMS FOR ON-HIGHWAY TRUCKS
SAE-J2203-1995 SAE 17.6 CUBIC INCH SPARK PLUG RATING ENGINE
SAE-J2204-1994 TIRE SIZE DIFFERENTIAL - ARTICULATED WHEEL LOADER, STANDARD - MAY 1994
SAE-J2208-1993 PARK STANDARD FOR AUTOMATIC TRANSMISSIONS, RECOMMENDED PRACTICE - JUNE 1993
SAE-J2209-1999 CFC-12 (R-12) REFRIGERANT RECOVERY EQUIPMENT FOR MOBILE AUTOMOTIVE AIR-CONDITIONING SYSTEMS
SAE-J2210-1999 HFC-134A (R-134A) RECOVERY/RECYCLING EQUIPMENT FOR MOBILE AIR-CONDITIONING SYSTEMS
SAE-J2211-1998 RECOMMENDED SERVICE PROCEDURE FOR THE CONTAINMENT OF HFC-134A (R-134A)
SAE-J2212-1993 ACCELERATED EXPOSURE OF AUTOMOTIVE INTERIOR TRIM COMPONENTS USING A CONTROLLED IRRADIANCE AIR-COOLED XENON-ARC
APPARATUS, RECOMMENDED PRACTICE - MARCH 1993
SAE-J2213-1991 METRIC BALL JOINTS, STANDARD - JUNE 1991
SAE-J2215-1991 SURFACE MATCH VERIFICATION METHOD FOR PRESSURE SENSITIVE ADHESIVELY ATTACHED COMPONENTS
SAE-J2217-1991 PHOTOMETRIC GUIDELINES FOR INSTRUMENT PANEL DISPLAYS THAT ACCOMMODATE OLDER DRIVERS, INFORMATION REPORT -
OCTOBER 1991
SAE-J2219-1994 (R) MOBILE AIR CONDITIONING INDUSTRY CRITERIA AND GUIDELINES, INFORMATION REPORT - OCTOBER 1994
SAE-J2221-1998 STANDARDIZED SYMBOLS FOR ELECTRICAL CIRCUIT DIAGRAMS
SAE-J222-2000 (R) PARKING LAMPS (FRONT POSITION LAMPS)
SAE-J2222-1993 COILED ELECTRICAL CABLE, TECHNICAL REPORT - NOVEMBER 1993
SAE-J2223-1-2005 CONNECTIONS FOR ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSES PART 1: SINGLE-POLE CONNECTORSFLAT BLADE
TERMINALS DIMENSIONAL CHARACTERISTICS AND SPECIFIC REQUIREMENTS
SAE-J2223-2-2005 (R) CONNECTIONS FOR ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSES PART 2: TESTS AND GENERAL PERFORMANCE
REQUIREMENTS
SAE-J2223-3-2006 CONNECTIONS FOR ON-BOARD ROAD VEHICLE ELECTRICAL WIRING HARNESSESPART 3: MULTIPOLE CONNECTORS FLAT BLADE
TERMINALSDIMENSIONAL CHARACTERISTICS AND SPECIFIC REQUIREMENTS
SAE-J2224-2002 IDENTIFICATION OF TRUCK, TRAILER, AND BUS WHEEL SEALS AND ASSOCIATED PACKAGING
SAE-J2226-1992 INTERNAL COMBUSTION ENGINES - PISTON RINGS - STEEL RECTANGULAR RINGS
SAE-J2227-2002 INTERNATIONAL TESTS AND SPECIFICATIONS FOR AUTOMOTIVE ENGINE OILS
SAE-J2228-1993 KINGPIN WEAR LIMITS - COMMERCIAL TRAILERS AND SEMITRAILERS
SAE-J2229-1993 ACCELERATED EXPOSURE OF AUTOMOTIVE INTERIOR TRIM MATERIALS USING AN OUTDOOR UNDER GLASS VARIABLE ANGLE
CONTROLLED TEMPERATURE APPARATUS, STANDARD - FEBRUARY 1993
SAE-J2230-1993 ACCELERATED EXPOSURE OF AUTOMOTIVE INTERIOR TRIM MATERIALS USING OUTDOOR UNDER-GLASS CONTROLLED SUN-TRACKING
TEMPERATURE AND HUMIDITY APPARATUS, STANDARD; - FEBRUARY 1993
SAE-J2232-1992 VEHICLE SYSTEM VOLTAGE - INITIAL RECOMMENDATIONS
SAE-J2233-2002 BUS BODY HEATING SYSTEM TEST
SAE-J2234-2001 EQUIVALENT TEMPERATURE
SAE-J2235-1999 PAINT AND TRIM CODE LOCATION
SAE-J2236-1999 STANDARD METHOD FOR DETERMINING CONTINUOUS UPPER TEMPERATURE RESISTANCE OF ELASTOMERS
SAE-J2237-1995 HEAVY-DUTY STARTER REMANUFACTURING PROCEDURES, RECOMMENDED PRACTICE - FEBRUARY 1995
SAE-J2238-2001 AIRBAG INFLATOR BALLISTIC TANK TEST PROCEDURE GAS GENERATORS USED IN INFLATABLE RESTRAINT SYSTEMS
SAE-J2240-1993 STARTER ARMATURE REMANUFACTURING PROCEDURES
SAE-J2241-1993 AUTOMOTIVE STARTER DRIVE REMANUFACTURING PROCEDURES
SAE-J224-1980 COLLISION DEFORMATION CLASSIFICATION - MARCH 1980
SAE-J2242-1993 AUTOMOTIVE STARTER SOLENOID REMANUFACTURING PROCEDURES
SAE-J2244-1-1991 CONNECTIONS FOR FLUID POWER AND GENERAL USE - PORTS AND STUD ENDS WITH ISO 261 THREADS AND O-RING SEALING
PART 1: PORT WITH O-RING SEAL IN TRUNCATED HOUSING - ISO 6149-1
SAE-J2244-2-1991 CONNECTIONS FOR FLUID POWER AND GENERAL USE - PORTS AND STUD ENDS WITH ISO 261 THREADS AND O-RING SEALING
PART 2: HEAVY-DUTY (S SERIES) STUD ENDS - DIMENSIONS, DESIGN, TEST METHODS, AND REQUIREMENTS - ISO 6149-2
SAE-J2244-3-1998 CONNECTIONS FOR FLUID POWER AND GENERAL USE - PORTS AND STUD ENDS WITH ISO 261 METRIC THREADS AND O-RING
SEALING, PART 3: LIGHT-DUTY (L SERIES) STUD ENDS - DIMENSIONS, DESIGN, TEST METHODS, AND REQUIREMENTS
SAE-J2244-4-1997 CONNECTIONS FOR FLUID POWER AND GENERAL USE - PORTS AND STUD ENDS WITH ISO 261 THREADS AND O-RING SEALING -
PART 4: HEAVY-DUTY (S SERIES) EXTERNAL HEX PORT PLUGS - DIMENSIONS, DESIGN, TEST METHODS, AND REQUIREMENTS
SAE-J2245-1994 RECOMMENDED PRACTICE FOR SPLASH AND SPRAY EVALUATION
SAE-J2246-1992 ANTILOCK BRAKE SYSTEM REVIEW, INFORMATION REPORT - JUNE 1992
SAE-J2247-2001 TRUCK TRACTOR POWER OUTPUT FOR TRAILER ABS
SAE-J2249-1999 WHEELCHAIR TIEDOWN AND OCCUPANT RESTRAINT SYSTEMS FOR USE IN MOTOR VEHICLES
SAE-J225-2003 BRAKE FORCE DISTRIBUTION FIELD TEST PROCEDURE FOR TRUCK AND BUS
SAE-J2253-1995 TEST PROCEDURES FOR AUTOMOTIVE STRUCTURAL COMPOSITE MATERIALS, STANDARD - DECEMBER 1995
SAE-J2254-1995 FLUID POWER PIPING CLEANING PROCESS, INFORMATION REPORT - SEPTEMBER 1995
SAE-J2255-1996 ANTILOCK BRAKE SYSTEMS ENERGY CONSUMPTION TEST PROCEDURE FOR AIR-BRAKED-EQUIPPED TRUCK TRACTORS, BUSES,
TRAILERS, AND DOLLIES, RECOMMENDED PRACTICE - MAY 1996
SAE-J2258-2003 (R) LIGHT UTILITY VEHICLES
SAE-J2260-2004 NONMETALLIC FUEL SYSTEM TUBING WITH ONE OR MORE LAYERS
SAE-J2261-2002 STOP LAMPS AND FRONT- AND REAR-TURN SIGNAL LAMPS FOR USE ON MOTOR VEHICLES 2032 MM OR MORE IN OVERALL WIDTH
SAE-J226-1995 (R) ENGINE PREHEATERS
SAE-J2263-1996 ROAD LOAD MEASUREMENT USING ONBOARD ANEMOMETRY AND COASTDOWN TECHNIQUES
SAE-J2264-1995 CHASSIS DYNAMOMETER SIMULATION OF ROAD LOAD USING COASTDOWN TECHNIQUES, RECOMMENDED PRACTICE - APRIL 1995
SAE-J2265-1995 DIESEL ENGINES - DIESEL FUEL - PERFORMANCE REQUIREMENT AND TEST METHOD FOR ASSESSING FUEL LUBRICITY, STANDARD;
- JUNE 1995
SAE-J2266-2004 LOCATION REFERENCING MESSAGE SPECIFICATION (LRMS)
SAE-J2270-1998 SHIP SYSTEMS AND EQUIPMENTTHREADED FASTENERSINSPECTION, TEST, AND INSTALLATION REQUIREMENTS
SAE-J2271-1996 SHIP SYSTEMS AND EQUIMENT PART STANDARD FOR STUDS CONTINOUS AND DOUBLE END (INCH SERIES)
SAE-J2271M-1996 SHIP SYSTEMS AND EQUIPMENT - PART STANDARD FOR STUDS - CONTINUOUS AND DOUBLE END (METRIC)
SAE-J2275-1996 INTERNAL COMBUSTION ENGINES - PISTON RING-GROOVES, STANDARD - JULY 1996
SAE-J2276-1998 NUMBERING SYSTEM FOR MULTIPLE DIAMETER CUTTING TOOLS
SAE-J2277-2003 SHOT PEENING COVERAGE
SAE-J2280-1996 SHIP SYSTEMS AND EQUIPMENT - FASTENERS - SELECTION AND IDENTIFICATION REQUIREMENTS, STANDARD - APRIL 1996
SAE-J2281-1997 SELECTING AND SPECIFYING HOT-ROLLED STEEL BAR PRODUCTS
SAE-J228-1990 AIRFLOW REFERENCE STANDARDS
SAE-J2282-2002 (R) DISTRIBUTED LIGHTING SYSTEMS (DLS)
SAE-J2283-2005 MECHANICAL AND MATERIAL REQUIREMENTS FOR ONE PIECE WHEEL NUTS
SAE-J2284-1-2002 HIGH SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 125 KBPS
SAE-J2284-2-2002 HIGH SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 250 KBPS
SAE-J2284-3-2002 HIGH-SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 500 KBPS
SAE-J2286-1997 VENDOR COMPONENT PROGRAM DATA FILE INTERFACE FOR OEM ASSEMBLY OPERATIONS
SAE-J2287-1999 RECOMMENDED DESIGN AND PERFORMANCE STANDARD FOR SEATS WITH INTEGRATED LAP AND SHOULDER RESTRAINTS
SAE-J2288-1997 LIFE CYCLE TESTING OF ELECTRIC VEHICLE BATTERY MODULES
SAE-J2289-2000 ELECTRIC DRIVER BATTERY PACK SYSTEM FUNCTIONAL GUIDELINES
SAE-J229-1971 SERVICE BRAKE STRUCTURAL INTEGRITY TEST PROCEDURE - PASSENGER CAR
SAE-J2292-2000 COMBINATION PELVIC/UPPER TORSO (TYPE 2) OPERATOR RESTRAINT SYSTEMS FOR OFF-ROAD WORK MACHINES
SAE-J2293-1-1997 ENERGY TRANSFER SYSTEM FOR ELECTRIC VEHICLES - PART 1: FUNCTIONAL REQUIREMENTS AND SYSTEM ARCHITECTURES
SAE-J2293-2-1997 ENERGY TRANSFER SYSTEM FOR ELECTRIC VEHICLES - PART 2: COMMUNICATION REQUIREMENTS AND NETWORK ARCHITECTURE
SAE-J2295-2006 FASTENER PART STANDARD - CAPS SCREWS, HEX BOLTS, AND HEX NUTS (INCH DIMENSIONED)
SAE-J2296-1998 RETEST OF REFRIGERANT CONTAINER
SAE-J2297-1996 ULTRAVIOLET LEAK DETECTION: STABILITY AND COMPATIBILITY CRITERIA OF FLUORESCENT REFRIGERANT LEAK DETECTION
DYES FOR MOBILE R-134A AIR- CONDITIONING SYSTEMS, STANDARD - SEPTEMBER 1996
SAE-J2298-1996 ULTRAVIOLET LEAK DETECTION: PROCEDURE FOR USE OF REFRIGERANT LEAK DETECTION DYES FOR SERVICE OF MOBILE AIR-
CONDITIONING SYSTEMS, STANDARD - SEPTEMBER 1996
SAE-J2299-1996 ULTRAVIOLET LEAK DETECTION: PERFORMANCE REQUIREMENTS FOR FLUORESCENT REFRIGERANT LEAK DETECTION DYE INJECTION
EQUIPMENT FOR AFTERMARKET SERVICE OF MOBILE AIR- CONDITIONING SYSTEMS, STANDARD - SEPTEMBER 1996
SAE-J2301-2005 UNIVERSAL JOINT END YOKE CONNECTION (EARWORK)
SAE-J230-1994 (R) STAINLESS STEEL, SAE 30302, SPRING WIRE AND SPRINGS - JUNE 1994
SAE-J2302-1996 THERMAL EFFECTIVENESS OF SLEEVE INSULATION
SAE-J2305-2002 SAFETY FOR HORIZONTAL EARTHBORING MACHINES
SAE-J2310-1999 RECTANGULAR CROSS SECTION POLYMERIC SEALING RINGS (METRIC)
SAE-J2311-1999 AUTOMATIC TRANSMISSION HYDRAULIC PUMP TEST PROCEDURE
SAE-J2312-2005 AUTOMATIC TRANSMISSION INTAKE FILTER TEST PROCEDURE
SAE-J2313-1999 ON-BOARD LAND VEHICLE MAYDAY REPORTING INTERFACE
SAE-J2314-2000 ETHICS FOR ACCIDENT INVESTIGATION AND RECONSTRUCTION
SAE-J2315-1998 WHEEL NUT SEAT STRENGTH
SAE-J2316-1998 WHEEL NUT SEAT SYSTEM TEST PROCEDURES AND PERFORMANCE REQUIREMENTS FOR PASSENGER CARS AND LIGHT TRUCKS
SAE-J2317-1996 TAMPER RESISTANCE FOR ADJUSTABLE PARAMETERS ON DIESEL FUEL INJECTION PUMPS
SAE-J2318-2002 AIR BRAKE ACTUATOR TEST PERFORMANCE REQUIREMENTS
SAE-J2319-1997 LOW-SPEED IMPACT BUMPER SYSTEM TEST PROCEDURE FOR PASSENGER VEHICLES
SAE-J2320-2001 DISCHARGE SIGNAL LIGHTNING SYSTEM
SAE-J2321-1-2000 DISPOSABLE HYDRAULIC FILTER ELEMENT - 115L/MIN FLOW, 1.0 MPA COLLAPSE PRESSURE, FILTRATION RATIO = 75 AT 6
AND 10 UM
SAE-J2321-2002 SHIP SYSTEMS AND EQUIPMENTGENERAL SPECIFICATION FOR FILTER ELEMENTSHYDRAULIC AND LUBE OIL SERVICE
SAE-J2321-2-2000 DISPOSABLE HYDRAULIC FILTER ELEMENT - 190 L/MIN FLOW, 21 MPA COLLAPSE PRESSURE, FILTRATION RATIO = 75 AT 7
UM
SAE-J2321-3-2000 DISPOSABLE HYDRAULIC FILTER ELEMENTS - 21 MPA COLLAPSE PRESSURE, FILTRATION RATIO = 75 AT 10 UM, 75 TO 175
L/MIN
SAE-J232-2003 INDUSTRIAL ROTARY MOWERS
SAE-J2329-1997 CATEGORIZATION AND PROPERTIES OF LOW-CARBON AUTOMOTIVE SHEET STEELS
SAE-J2330-1998 WALK-ALONG WORK MACHINESBRAKING SYSTEMSPERFORMANCE REQUIREMENTS AND TEST PROCEDURES
SAE-J2331-1996 OPERATOR'S FIELD OF VIEW-ENGINEERING EVALUATION
SAE-J2332-1997 MARKING OF RUBBER PARTS
SAE-J2333-1998 SHIP SYSTEMS AND EQUIPMENT - HYDRAULIC SYSTEMS - FILTER SELECTION PARAMETERS
SAE-J2334-2003 LABORATORY CYCLIC CORROSION TEST
SAE-J2337-1-2002 CONNECTIONS FOR FLUID POWER AND HIGH PRESSURE USEPORTS, STUD ENDS, AND PLUGS WITH ISO 261 THREADS AND O-RING
SEALINGPART 1: PORTS WITH RECESSED CONICAL SEAT REQUIREMENTS, DIMENSIONS, DESIGN, AND TEST METHODS
SAE-J2337-2-2002 CONNECTIONS FOR FLUID POWER AND HIGH PRESSURE USE PORTS, STUD ENDS, AND PLUGS WITH ISO 261 THREADS AND O-
RING SEALINGPART 2: STUD END REQUIREMENTS, DIMENSIONS, DESIGN, AND TEST METHODS
SAE-J2337-3-2002 CONNECTIONS FOR FLUID POWER AND HIGH PRESSURE USEPORTS, STUD ENDS, AND PLUGS WITH ISO 261 THREADS AND O-RING
SEALINGPART 3: PORT PLUG REQUIREMENTS, DIMENSIONS, DESIGN, AND TEST METHODS
SAE-J2340-1999 CATEGORIZATION AND PROPERTIES OF DENT RESISTANT, HIGH STRENGTH, AND ULTRA HIGH STRENGTH AUTOMOTIVE SHEET STEEL
SAE-J234-1977 ELECTRIC WINDSHIELD WASHER SWITCH - OCTOBER 1977
SAE-J2342-1999 NUMBERING SYSTEMS FOR END MILLS
SAE-J2343-1997 RECOMMENDED PRACTICES FOR LNG POWERED HEAVY-DUTY TRUCKS
SAE-J2344-1998 GUIDELINES FOR ELECTRIC VEHICLE SAFETY
SAE-J2348-1997 ELECTRIC WINDSHIELD WASHER SWITCHTRUCKS, BUSES, AND MULTIPURPOSE VEHICLES
SAE-J2349-1997 ELECTRIC WINDSHIELD WIPER SWITCHTRUCKS, BUSES, AND MULTIPURPOSE VEHICLES
SAE-J2350-1997 ELECTRIC BLOWER MOTOR SWITCHTRUCKS, BUSES, AND MULTIPURPOSE VEHICLES
SAE-J235-1971 ELECTRIC BLOWER MOTOR SWITCH - MAY 1971
SAE-J2352-1998 MAYDAY INDUSTRY SURVEY INFORMATION REPORT
SAE-J2353-1999 DATA DICTIONARY FOR ADVANCED TRAVELER INFORMATION SYSTEMS (ATIS)
SAE-J2354-2004 MESSAGE SETS FOR ADVANCED TRAVELER INFORMATION SYSTEM (ATIS)
SAE-J2355-1997 ITS DATA BUS ARCHITECTURE REFERENCE MODEL INFORMATION REPORT
SAE-J2356-1997 GRAPHICAL MODEL FOR INTERACTIVE DISTRIBUTED CONTROL
SAE-J2357-2000 APPLICATION GUIDELINES FOR ELECTRONICALLY DRIVEN AND/OR CONTROLLED EXTERIOR AUTOMOTIVE LIGHTING EQUIPMENT
SAE-J2358-2002 LOW SPEED VEHICLES
SAE-J2359-1998 LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, MILITARY COMBAT/TACTICAL SERVICE
SAE-J2360-1998 LUBRICATING OIL, GEAR MULTIPURPOSE (METRIC) MILITARY USE
SAE-J2361-1998 LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATION BREAK-IN
SAE-J2362-2005 (R) LUBRICATING OIL, AUTOMOTIVE ENGINE, API SERVICE SM FOR MILITARY ADMINISTRATIVE SERVICE
SAE-J2363-2005 (R) LUBRICATING OIL FOR WHEELED MILITARY VEHICLES WITH HEAVY-DUTY DIESEL ENGINES
SAE-J2364-2004 NAVIGATION AND ROUTE GUIDANCE FUNCTION ACCESSIBILITY WHILE DRIVING
SAE-J2365-2002 CALCULATION OF THE TIME TO COMPLETE IN-VEHICLE NAVIGATION AND ROUTE GUIDANCE TASKS
SAE-J2366-1-2001 ITS DATA BUS - IDB-C PHYSICAL LAYER
SAE-J2366-1L-2001 ITS DATA BUS - LOW IMPEDANCE STEREO AUDIO (LISA)
SAE-J2366-2-2001 LINK LAYER
SAE-J2366-4-2002 ITS DATA BUSTHIN TRANSPORT LAYER
SAE-J2366-7-2002 ITS DATA BUSAPPLICATION MESSAGE LAYER
SAE-J2369-2000 STANDARDS FOR ATIS MESSAGE SETS DELIVERED OVER REDUCED BANDWIDTH MEDIA
SAE-J2370-2003 GEOMETRIC DIMENSIONS AND TOLERANCING FOR CURVED HOSE
SAE-J2371-1997 CLAMPING FORCE TEST PROCEDURE
SAE-J2372-1999 FIELD TEST ANALYSIS INFORMATION REPORT
SAE-J2373-2000 STAKEHOLDER- WORKSHOP INFORMATION REPORT
SAE-J2374-1999 LOCATION REFERENCING MESSAGE SPECIFICATION REFERENCING MEASSAGE SPECIFICATION
SAE-J2375-1997 SELECTION OF ADHESIVES FOR THE ATTACHMENT OF EXTERIOR AFTERMARKET ACCESSORIES
SAE-J2376-2005 NEW-VEHICLE COLLISION REPAIR INFORMATION
SAE-J2378-2003 TEST PROCEDURE FOR TRAILER AIR RESERVOIR FILL AND PARKING BRAKE RELEASE TIMES
SAE-J2379-1997 PERFORMANCE ENGINE BUILDING RECOMMENDED PRACTICES
SAE-J2380-1998 VIBRATION TESTING OF ELECTRIC VEHICLE BATTERIES
SAE-J238-1973 NUT AND CONICAL SPRING WASHER ASSEMBLIES
SAE-J2382-2000 VIDEO BASED LIGHT MEASUREMENT TECHNIQUES
SAE-J2383-1998 AIR DRYER INSTALLATION PROCEDURE
SAE-J2384-1999 AIR DRYER TEST PROCEDURE
SAE-J2387-2003 DIMENSIONS AND TOLERANCES FOR COOLANT SYSTEM HOSES
SAE-J2388-2002 SECONDARY CONTROL MODIFICATIONS
SAE-J2392-2003 CATEGORIZATION AND PROPERTIES OF SAE COLD ROLLED STRIP STEELS
SAE-J2394-1998 SEVEN-CONDUCTOR CABLE FOR ABS POWER
SAE-J2395-2002 ITS IN-VEHICLE MESSAGE PRIORITY
SAE-J2396-2000 DEFINITIONS AND EXPERIMENTAL MEASURES RELATED TO THE SPECIFICATION OF DRIVER VISUAL BEHAVIOR USING VIDEO BASED
TECHNIQUES | 
